Datatek IP-DSU Скачать руководство пользователя страница 13

Страница: 13 / 48

I P - D S U U s e r ’ s M a n u a l

02/02/08

mounting rails 75 inches in height. This configuration would support a maximum of 84

IP-DSU

units.

A rack-mount panel for each set of twelve

IP-DSU

units.

A pair of mounting ears for each

IP-DSU

Strain-relief clamps for DC wire stabilization.

Power distribution module(s) (1 for every 6

IP-DSU

units)

3.2 Power Configuration Steps for 48V DC Operation

The

IP-DSU

is factory configured for 115V AC usage. 48V DC operation requires a

different jumper setting on the

IP-DSU

system board.

Disconnect any power connectors to the
IP-DSU.

Remove the IP-DSU cover, exposing the
top portion of the system board

Locate the jumper connector and move the
jumper to the 48V setting

(see adjacent

figure).

Replace the IP-DSU cover.

The IP-DSU is ready for 48V DC operation

3.3 Stand-alone

Installation

3.3.1 AC

ONLY

Attach the provided feet to the bottom of the unit.

Place the

IP-DSU

in the desired location, such as a shelf in a data equipment rack.

Plug one end of the RJ45-terminated category 5 twisted-pair data cable into the

IP-DSU

10BaseT LAN interface, and the other into a 10BaseT LAN hub or router.

Plug one end of the RJ45-terminated twisted-pair data cable into the

IP-DSU

console

interface, and the other into the port of the asynchronous device that will be used to
configure or manage the

IP-DSU

Содержание IP-DSU

















































Результаты поиска

Содержание IP-DSU

Отзывы:

Похожие инструкции для IP-DSU

Бренды по названию

Популярные бренды

Datatek IP-DSU, Руководство пользователя

Результаты поиска

Содержание IP-DSU

Отзывы:

Похожие инструкции для IP-DSU

Бренды по названию

Популярные бренды