Datatek IP-DSU Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 48

background image

I P - D S U U s e r ’ s M a n u a l

02/02/08

19

3.7 Field Upgrade and Software Registration

The

IP-DSU,

when initially delivered, is fully registered and does not need any keys to

activate the software. Software keys are required when an optional individual feature
packages is added to the device. Finally, when the

IP-DSU

is upgraded with revised

software, one or more software keys are required to register the installed software and
any feature packages registered for the device.

When performing an upgrade, the revised software is initially downloaded by

upgrade

4

into a staging area and is not active. The software then is activated by a

reboot

. The

new software will execute normally prior to registration. However, no backup, reloads, or
upgrades can be performed. Module level parameters, such as the device IP address,
may be changed and activated. If a user port is taken out of service, the port cannot be
restored.

The procedure for performing a software registration has been mechanized. Manual
procedures are error prone and not recommended. They are no longer covered in this
user manual.

The mechanized Software Upgrade Registration procedure allows simplified
administration of one or more devices. When a quantity of devices are upgraded,
manual software registration of each device has the potential of becoming increasingly
tedious. The mechanized software upgrade registration process was designed to
alleviate the problems associated with multiple device upgrades. It is also preferred for
single device upgrades as it eliminates any potential for error.

The new software is downloaded to the

IP-DSU

via the

upgrade

command. This may be

performed for one or more devices. The “-r” option to the dtupgrade command will restart
the device on the new software after the download completes successfully. It is highly
recommended. In the alternative, the device may be downloaded without a restart and
restarted at a later time during a scheduled maintenance window. Restarting the device
on the new software prior to registration is required. After the restart, the devices will
continue to operate normally on the new software without registration. Some operations
interface functions are inhibited pending software registration. Below is an example of a
typical

upgrade

invocation. Note the use of the “-r” option as it is recommended.

upgrade –v –d –r –i –mIP-DSU 10.0.1.42 ipdsu.21.1

4

The utilities may be renamed to any desired mnemonic. The names shown are those on the distribution.

«
...
17
18
19
20
21
...
»

Содержание IP-DSU

















































Отзывы:

Нет отзывов

Похожие инструкции для IP-DSU

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 66

Бренд: RTA Страницы: 66

RAK7243 Pilot Gateway Pro

Бренд: RAKwireless Страницы: 18

Бренд: Aaeon Страницы: 40

Бренд: VisionNet Страницы: 102

Бренд: ZyXEL Communications Страницы: 56

Бренд: Hans Turck Страницы: 53

Бренд: 2N Страницы: 101

Arctic Substation Gateway

Бренд: Viola Systems Страницы: 51

Arctic 3G Gateway 2622

Бренд: Viola Systems Страницы: 5

Бренд: UTC Fire and Security Страницы: 174

Бренд: XAVi Страницы: 101

Бренд: Abbott Страницы: 26

Бренд: ECOWITT Страницы: 61

OpenSource LEW840X Series

Бренд: Fanstel Страницы: 23

Бренд: Vantron Страницы: 110

Бренд: ICP DAS USA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды