manualshive.com logo in svg

Danfoss VLT HVAC FC 100, Руководство по обслуживанию, Страница: 35 / 220

Поделиться
Скачать
Danfoss VLT HVAC FC 100 Скачать руководство пользователя страница 35

Standby

[Auto On] The adjustable frequency drive starts the motor using a start signal in a digital input (if
the parameter is programmed accordingly) or via serial communication.

Start delay

In par. 1-71 

Start Delay

, the delay of the starting time was set. A Start command was activated

and the delay time is still running. The motor will start after the delay time has expired.

Start fwd/rev

Enable start forward

 and 

Enable start reverse

 were selected as functions for two different digital

inputs (parameter group 5-1*). To start the motor, a direction dependent start signal has to be
given and the corresponding terminal has to be active.

Start inhibit

PROFIDrive profile

 was selected in par. 8-10 

Control Word Profile

. The start inhibition is active.

The adjustable frequency drive needs the first part (e.g., 0x047E) of the two-part start command
via serial communication to allow starting. See also operation status control ready.

Stop

[Off] was pressed on the LCP or Stop inverse was selected as a function for a digital input (Group
5-1*). The corresponding terminal is not active.

Trip

An alarm occurred. It is possible, provided the cause of the alarm is cleared, to reset the alarm
via a 

Reset

 signal ([Reset] key on the LCP, a control terminal or serial communication).

Trip lock

A serious alarm occurred. It is possible, provided the cause of the alarm was cleared, to reset the
alarm after line power has been switched off and on again. This can be done via a

 reset

 signal

([Reset] on the LCP, a control terminal or serial communication).

Unit/Drive not ready

PROFIDrive profile

 was selected in par. 8-10 

Control Word Profile

. A control word is sent to the

adjustable frequency drive via serial communication with Off 1, Off 2 and Off 3 active. Start inhibit
is active. To enable start, see operation status Start inhibit.

2 Operator Interface and Adjustable Frequen-

cy Drive Control

High Power Service Manual for VLT

®

 FC Series

Adjustable Frequency Drives

2-12

MG.90.L1.22 - VLT

®

 is a registered Danfoss trademark

2  

Содержание VLT HVAC FC 100





























































































































































































































Отзывы:

Нет отзывов