background image

18 

User 

Guide RS8GD602 © Danfoss 2015-10 

Optyma 

Plus 

TM

AD

AP

-K

OOL®

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products 

already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respecitve companies. Danfoss and Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

Ordering

Type

Function

Code no.

Optyma Plus

TM

Condensing unit controller

Prepared for  data communication

Plug for screw terminals not enclosed

084B8080

Plug

Plug with screw terminals

084B8166

EKA 175

Data communication module LON RS485

084B8579

EKA 163B

External display with plug for direct connection

084B8574

EKA 164B

External display with operation buttons and plug for direct 

connections

084B8575

EKA 163A

External display with screw terminals

084B8562

EKA 164A

External display with operation buttons and screw terminals

084B8563

Wire with plug

Wire for  display unit (9 m, with plug)

084B7630

(24 pcs.)

EKA 183A

Programming key

084B8582

Содержание Optyma Plus



















Отзывы: