![background image](http://html2.mh-extra.com/html/danfoss/d9h/d9h_operating-manual_5121583040.webp)
•
•
•
•
•
•
•
•
•
-
-
-
-
-
-
Tape measurer.
Phillips and flat-bladed screwdrivers.
Wrench with 7–17 mm metric sockets.
Wrench extensions.
T25 and T50 Torx drives.
Sheet metal punch and/or pliers for cable entry plate.
4.4 Storing the Drive
Store the drive in a dry location. Keep the equipment sealed in its packaging until installation. Refer to the
Ambient Conditions
section for recommended ambient temperature.
Periodic forming (capacitor charging) is not necessary during storage unless storage exceeds 12 months.
4.5 Operating Environment
4.5.1 Overview
In environments with airborne liquids, particles, or corrosive gases, ensure that the IP/NEMA protection rating of the equipment
matches the installation environment. Refer to the
Ambient Conditions
section.
N O T I C E
CONDENSATION
Moisture can condense on the electronic components and cause short circuits.
Avoid installation in areas subject to frost.
Install an optional space heater when the unit is colder than the ambient air.
Operating in standby mode reduces the risk of condensation as long as the power dissipation keeps the circuitry free of
moisture.
N O T I C E
EXTREME AMBIENT CONDITIONS
Hot or cold temperatures compromise unit performance and longevity.
Do not operate in environments where the ambient temperature exceeds 50 °C (122 °F) for units rated at 400–500 V and
45 °C (113 °F) for units rated at 525–690 V unless the drive is derated. Refer to the
Derating section
in the design guide.
The unit can operate at temperatures down to -10 °C (14 °F). However, proper operation at rated load is only guaranteed at
0 °C (32 °F) or higher. Also, temperature feedback is not shown when temperatures are below 0 °C (32 °F).
Provide extra air conditioning for the cabinet or installation site when the temperature exceeds ambient temperature limits.
4.5.2 Gases
Aggressive gases, such as hydrogen sulphide, chlorine, or ammonia can damage the electrical and mechanical components. The
unit uses conformal-coated circuit boards to reduce the effects of aggressive gases.
For conformal coating class specifications and ratings, see the
Ambient Conditions
section.
4.5.3 Dust
When installing the unit in a dusty environment, keep the following free from dust buildup:
Electronic components.
Heat sink.
Fans.
Keep the heat sink and fans free from dust buildup. When dust accumulates on electronic components, it acts as a layer of insula-
tion. This layer reduces the cooling capacity of the components, and the components become warmer. The hotter environment
decreases the life of the electronic components. Dust can also accumulate on fan blades, causing an imbalance which prevents the
fan from properly cooling the unit. Dust buildup can also damage fan bearings and cause premature fan failure.
For more information, refer to the
Maintenance and Service
section.
AQ262139143212en-000301 / 130R0879
40 | Danfoss A/S © 2021.10
Mechanical Installation
VLT® AutomationDrive FC 302
Operating Guide
Содержание D9h
Страница 2: ......
Страница 11: ...AQ262139143212en 000301 130R0879 11 Danfoss A S 2021 10 Introduction VLT AutomationDrive FC 302 Operating Guide...
Страница 12: ...AQ262139143212en 000301 130R0879 12 Danfoss A S 2021 10 Introduction VLT AutomationDrive FC 302 Operating Guide...
Страница 13: ...AQ262139143212en 000301 130R0879 13 Danfoss A S 2021 10 Introduction VLT AutomationDrive FC 302 Operating Guide...