Danfoss D9h, Руководство по эксплуатации

Страница: 168 / 206

FC 302 N200 N250 N315
Intermittent (60 s overload) (at 575/690 V) [A] 363 319 435 378 516 440
Continuous kVA (at 550 V) [kVA] 230 276 276 327 327 380
Continuous kVA (at 575 V) [kVA] 241 289 289 343 343 398
Continuous kVA (at 690 V) [kVA] 289 347 347 411 411 478
Maximum input current
Continuous (at 525 V) [A] 244 292 292 347 347 403
Continuous (at 575/690 V) [A] 233 279 279 332 332 385
Maximum number and size of cables per phase
- Mains [mm
2
(AWG)] 2x185 (2x350 mcm) 2x185 (2x350 mcm) 2x185 (2x350 mcm)
- Mains with disconnect [mm
2
(AWG)] 2x185 (2x350 mcm) 2x185 (2x350 mcm) 2x185 (2x350 mcm)
- Mains with fusible disconnect [mm
2
(AWG)] 2x185 (2x350 mcm) 2x185 (2x350 mcm) 2x185 (2x350 mcm)
- Mains with contactor [mm
2
(AWG)] 2x185 (2x350 mcm) 2x185 (2x350 mcm) 2x185 (2x350 mcm)
- Motor [mm
2
(AWG)] 2x185 (2x350 mcm) 2x185 (2x350 mcm) 2x185 (2x350 mcm)
Drive module power loss at 600 V [W]
(1)(2)(3)
3012 3723 3642 4465 4146 5028
Drive module power loss at 690 V [W]
(1)(2)(3)
3123 3851 3771 4614 4258 5155
Drive efficiency
(2)
0.98 0.98 0.98
Output frequency [Hz]
(4)
0–590 0–590 0–590
Heat sink overtemperature trip [°C (°F)] 110 (230) 110 (230) 110 (230)
Control card overtemperature trip [°C (°F)] 80 (176) 80 (176) 80 (176)
PHF overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302)
Line reactor overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302)
dU/dt filter overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302)
Sine-wave filter overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302)
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficien-
cy class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses section.
4
If using an output filter, the output frequency is limited further. See 10.3.1 Motor Output (U, V, W) .
Table 107: Electrical Data, Mains Supply 3x525–690 V AC
FC 302 N355 N400 N500
High/normal overload HO NO HO NO HO NO
AQ262139143212en-000301 / 130R0879 168 | Danfoss A/S © 2021.10
Specifications
VLT® AutomationDrive FC 302
Operating Guide