Danfoss D9h, Руководство по эксплуатации

Страница: 167 / 206

FC 302 N90K N110 N132 N160
- Mains with disconnect [mm
2
(AWG)] 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x185 (2x350 mcm)
- Mains with fusible disconnect [mm
2
(AWG)] 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x185 (2x350 mcm)
- Mains with contactor [mm
2
(AWG)] 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x185 (2x350 mcm)
- Motor [mm
2
(AWG)] 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x95 (2x3/0 mcm) 2x185 (2x350 mcm)
Drive module power loss at 600 V [W]
(1)(2)(3)
1430 1740 1742 2101 2080 2649 2361 3074
Drive module power loss at 690 V [W]
(1)(2)(3)
1480 1798 1800 2167 2159 2740 2446 3175
Drive efficiency
(2)
0.98 0.98 0.98 0.98
Output frequency [Hz] (4) 0–590 0–590 0–590 0–590
Heat sink overtemperature trip [°C (°F)] 110 (230) 110 (230) 110 (230) 110 (230)
Control card overtemperature trip [°C (°F)] 75 (167) 75 (167) 75 (167) 75 (167)
PHF overtemperature trip [°C (°F)] 145 (293) 145 (293) 145 (293) 145 (293)
Line reactor overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302)
dU/dt filter overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302)
Sine-wave filter overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302)
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
2 Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficien-
cy class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses section.
4
If using an output filter, the output frequency is limited further. See 10.3.1 Motor Output (U, V, W) .
Table 106: Electrical Data, Mains Supply 3x525–690 V AC
FC 302 N200 N250 N315
High/normal overload
High overload=150% or 160% torque for a duration of 60 s.
Normal overload=110% torque for a duration of 60 s.
HO NO HO NO HO NO
Typical shaft output at 550 V [kW] 160 200 200 250 250 315
Typical shaft output at 575 V [hp] 250 300 300 350 350 400
Typical shaft output at 690 V [kW] 200 250 250 315 315 400
Enclosure size
D10h D10h D10h
Output current (3-phase)
Continuous (at 550 V) [A] 253 303 303 360 360 418
Intermittent (60 s overload) (at 550 V) [A] 380 333 455 396 540 460
Continuous (at 575/690 V) [A] 242 290 290 344 344 400
AQ262139143212en-000301 / 130R0879 | 167 Danfoss A/S © 2021.10
Specifications
VLT® AutomationDrive FC 302
Operating Guide