Danfoss D9h, Руководство по эксплуатации

Страница: 164 / 206

FC 302 N315 N355 N400
Intermittent (60 s overload) (at 460/500 V) [A] 810 649 885 746 1017 803
Continuous kVA (at 400 V) [kVA] 416 456 456 516 482 554
Continuous kVA (at 460 V) [kVA] 430 470 470 540 540 582
Continuous kVA (at 500 V) [kVA] 468 511 511 587 587 632
Maximum input current
Continuous (at 400 V) [A] 578 634 634 718 670 771
Continuous (at 460/500 V) [A] 520 569 569 653 653 704
Maximum number and size of cables per phase
- Mains [mm
2
(AWG)] 4x127 (4x250 mcm) 4x127 (4x250 mcm) 4x127 (4x250 mcm)
- Mains with disconnect [mm
2
(AWG)] 4x127 (4x250 mcm) 4x127 (4x250 mcm) 4x127 (4x250 mcm)
- Mains with fusible disconnect [mm
2
(AWG)] 4x127 (4x250 mcm) 4x127 (4x250 mcm) 4x127 (4x250 mcm)
- Mains with contactor [mm
2
(AWG)] 4x127 (4x250 mcm) 4x127 (4x250 mcm) 4x127 (4x250 mcm)
- Motor [mm
2
(AWG)] 4x127 (4x250 mcm) 4x127 (4x250 mcm) 4x127 (4x250 mcm)
Drive module power loss at 400 V [W]
(1)(2)(3)
6178 6928 6851 8036 7297 8783
Drive module power loss at 460 V [W]
(1)(2)(3)
5322 5910 5846 6933 7240 7969
Drive efficiency
(2)
0.98 0.98 0.98
Output frequency [Hz]
(4)
0–590 0–590 0–590
Heat sink overtemperature trip [°C (°F)] 110 (230) 110 (230) 110 (230)
Control card overtemperature trip [°C (°F)] 80 (176) 80 (176) 80 (176)
PHF overtemperature trip [°C (°F)] 145 (293) 145 (293) 145 (293)
Line reactor overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302)
dU/dt filter overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302)
Sine-wave filter overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302)
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficien-
cy class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses section.
4
If using an output filter, the output frequency is limited further. See 10.3.1 Motor Output (U, V, W) .
Table 104: Electrical Data, Mains Supply 3x380–500 V AC
FC 302 N450 N500
High/normal overload HO NO HO NO
AQ262139143212en-000301 / 130R0879 164 | Danfoss A/S © 2021.10
Specifications
VLT® AutomationDrive FC 302
Operating Guide