Daktronics VFC-3000 Скачать руководство пользователя страница 52

Страница: 52 / 55

– 48 –

The central controller cannot

communicate with a particular

display.

The modem at the remote site

is not turned on or does not

have power.

Go to the site and check

power.

The modem at the site is

disconnected from the

communication network or the

VFC-3000 controller, or 1 of the

cables is bad.

Go to the site and check the

connections.

The modem at the remote site

is bad.

Replace the modem.

The central software network

settings are incorrect.

Ensure the network settings in

the software are correct.

The VFC-3000 software is

corrupted.

Reset the VFC-3000 controller.

Then download new firmware

to the VFC-3000 controller.

The processor board in the

VFC-3000 controller is bad.

Replace the VFC-3000

controller.

The surge arrester in the VFC-

3000 controller is bad.

Replace the surge arrester.

Another component in the

VFC-3000 controller is bad.

Contact Daktronics Customer

Service.

Power at the site is bad.

Get power restored at the site.

The VFC-3000 address is wrong. Correct the VFC-3000 address.

The INI file on the VFC-3000

controller is wrong or is corrupt.

Connect a laptop at

the display site to J31 at

28800 baud. If successful,

download the correct INI

file. If unsuccessful, contact

Daktronics Customer Service.

Содержание VFC-3000
























































Результаты поиска

Содержание VFC-3000

Отзывы:

Похожие инструкции для VFC-3000

Бренды по названию

Популярные бренды

Daktronics VFC-3000, Руководство по эксплуатации

Результаты поиска

Содержание VFC-3000

Отзывы:

Похожие инструкции для VFC-3000

Бренды по названию

Популярные бренды