D-Link DES-3010F Скачать руководство пользователя

Страница: 83 / 187

DES-3000 Series Layer 2 Switch CLI Reference Manual

config multicast filtering_mode

Purpose

Used to configure the multicast packet filtering mode for the Switch.

Syntax

config multicast filtering_mode [forward_unregistered_groups |
filter_unregistered_groups]

Description

This command will configure the multicast packet filtering mode on the
Switch.

Parameters

[forward_unregistered_groups | filter_unregistered_groups]

– The user may

set the filtering mode to any of these two options.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure the multicast filtering mode to filter unregistered groups.

DES-3026:4#config multicast filtering_mode filter_unregistered_groups
Command: config multicast filtering_mode filter_unregistered_groups

Success.

DES-3026:4#

show multicast filtering_mode

Purpose

Used to show the multicast packet filtering.

Syntax

show multicast filtering_mode

Description

This command will display the current multicast packet filtering
mode on the Switch.

Parameters None.

Restrictions None.

Example usage:

To view the multicast filtering mode configuration:

DES-3026:4#show multicast filtering_mode
Command: show multicast filtering_mode

Multicase Filter Mode : forward_unregistered_groups

DES-3026:4#

Содержание DES-3010F




























































































































































































Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды

D-Link DES-3010F, Руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды