D-Link DES-3010F Скачать руководство пользователя

Страница: 150 / 187

DES-3000 Series Layer 2 Switch CLI Reference Manual

config 802.1x auth_parameter ports

force_unauth

−

Forces the Authenticator for the port to become

unauthorized. Network access will be blocked.

quiet_period <sec 0-65535>

−

Configures the time interval between

authentication failure and the start of a new authentication attempt.

tx_period <sec 1-65535>

- Configures the time to wait for a response from a

supplicant (user) to send EAP Request/Identity packets.

supp_timeout <sec 1-65535>

- Configures the time to wait for a response

from a supplicant (user) for all EAP packets, except for the Request/Identity
packets.

server_timeout <sec 1-65535>

- Configure the length of time to wait for a

response from a RADIUS server.

max_req <value 1-10>

−

Configures the number of times to retry sending

packets to a supplicant (user).

reauth_period <sec 1-65535>

−

Configures the time interval between

successive re-authentications.

enable_reauth [enable | disable]

−

Determines whether or not the Switch

will re-authenticate. Enabled causes re-authentication of users at the time
interval specified in the Re-authentication Period field, above.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure 802.1x authentication parameters for ports 1 – 20:

DES-3026:4#config 802.1x auth_parameter ports 1 – 20 direction both
Command: config 802.1x auth_parameter ports 1 – 20 direction both

Success.

DES-3026:4#

config 802.1x auth_protocol

Purpose

Used to configure the 802.1x authentication protocol on the
Switch.

Syntax

config 802.1x auth_protocol [local | radius_eap]

Description

The

config 802.1x auth_protocol

command enables you to

configure the authentication protocol.

Parameters

[local | radius_eap]

– Specify the type of authentication protocol

desired.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure the authentication protocol on the Switch:

DES-3026:4# config 802.1x auth_protocol local
Command: config 802.1x auth_protocol local

Success.

DES-3026:4#

148

Содержание DES-3010F




























































































































































































Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды

D-Link DES-3010F, Руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды