D-Link DES-3010F Скачать руководство пользователя | Manualshive

Страница: 90 / 187

background image

DES-3000 Series Layer 2 Switch CLI Reference Manual

config cos mapping

•

ip

- Specifies port-based CoS mapping on selected ports to be

tos

or

dscp

mapping.

•

tos

– Specifies CoS mapping for Type of Service (ToS) priority. Select the ToS

value (

value <value 0 - 7>

) and the class (

class <class_id 0-3>

)

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure CoS to enable port-based CoS mapping:

DES-3026:4#config cos mapping port all port_mapping
Command: config cos mapping port all port_mapping

Success

DES-3026:4#

show cos mapping

Purpose

Used to show CoS mapping.

Syntax

show cos mapping {port <portlist> | all }

Description

The show cos mapping displays information regarding CoS mapping enabled ports and
their mapping method.

Parameters

portlist

−

Specified a range of ports to be displayed. If no parameter specified, all ports

priority settings will be shown.

Restrictions None.

Example usage:

To display CoS mapping configuration:

DES-3026:4#show cos mapping port 1-3
Command: show cos mapping port 1-3

Port Port priority Ethernet_priority IP_priority
-------------------------------------------------------------------------------
1 off 802.1p off
2 off 802.1p off
3 off 802.1p off

DES-3026:4#

config dscp_mapping

Purpose

To configure CoS mapping for DSCP (DiffServ) based priority.

Syntax

config dscp_mapping dscp_value <0–63> [class <class_id 0-3>]

Description

This is used to map the 64-level DSCP priority to the 4-level class of service
priority used in the Switch.

Parameters

dscp_value <0 – 63>

- The DSCP priority level being mapped. Each DSCP

level must be configured separately to be mapped.

class <class_id 0-3>

- The class of service level being mapped to.

Restrictions Only

administrator-level users can issue this command.

88

«
...
88
89
90
91
92
...
»

Содержание DES-3010F




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3010F

Бренд: Watchguard Страницы: 40

IES615-2D Series

Бренд: 3onedata Страницы: 3

Бренд: 3One data Страницы: 5

Бренд: 3onedata Страницы: 33

Бренд: Hama Страницы: 10

Бренд: Q-See Страницы: 2

Бренд: Clavister Страницы: 89

Бренд: process-informatik Страницы: 8

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

Бренд: WAGO Страницы: 2

Бренд: Asante Страницы: 150

UniFi WiFi BaseStation XG

Бренд: Ubiquiti Страницы: 19

Emotron OSTO 100

Бренд: CG Страницы: 112

Бренд: Xyclop Страницы: 144

Бренд: Silvertel Страницы: 9

Бренд: ADIC Страницы: 140

Бренд: Keysight Technologies Страницы: 106

Бренд: ADTRAN Страницы: 161

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды