D-Link DES-3010F Скачать руководство пользователя | Manualshive

Страница: 80 / 187

background image

DES-3000 Series Layer 2 Switch CLI Reference Manual

config fdb aging_time

Purpose

Used to set the aging time of the forwarding database.

Syntax

config fdb aging_time <sec 10-1000000>

Description

The aging time affects the learning process of the Switch. Dynamic
forwarding table entries, which are made up of the source MAC
addresses and their associated port numbers, are deleted from the
table if they are not accessed within the aging time. The aging time
can be from 10 to 1000000 seconds with a default value of 5
minutes (300 seconds). A very long aging time can result in dynamic
forwarding table entries that are out-of-date or no longer exist. This
may cause incorrect packet forwarding decisions by the Switch. If
the aging time is too short however, many entries may be aged out
too soon. This will result in a high percentage of received packets
whose source addresses cannot be found in the forwarding table, in
which case the Switch will broadcast the packet to all ports, negating
many of the benefits of having a Switch.

Parameters

<sec 10-1000000>

−

The aging time for the MAC address

forwarding database value, in seconds.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To set the fdb aging time:

DES-3026:4#config fdb aging_time 300
Command: config fdb aging_time 300

Success.

DES-3026:4#

delete fdb

Purpose

Used to delete an entry to the Switch’s forwarding database.

Syntax

delete fdb <vlan_name 32> <macaddr>

Description

This command is used to delete a previous entry to the Switch’s
MAC address forwarding database.

Parameters

<vlan_name 32>

−

The name of the VLAN on which the MAC

address resides.

<macaddr>

−

The MAC address that will be deleted from the

forwarding table.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To delete a permanent FDB entry:

DES-3026:4#delete fdb default 00-00-00-00-01-02
Command: delete fdb default 00-00-00-00-01-02

Success.

DES-3026:4#

78

«
...
78
79
80
81
82
...
»

Содержание DES-3010F




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3010F

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

Бренд: NETGEAR Страницы: 2

Бренд: Perle Страницы: 2

Бренд: Baicells Страницы: 10

Бренд: IBASE Technology Страницы: 39

Бренд: Asante Страницы: 150

301300U - Ethernet Disk NAS Server

Бренд: LaCie Страницы: 62

Бренд: SafeHome Страницы: 24

Temporary Target Board M38517T-ADS

Бренд: Renesas Страницы: 14

Digi Connect WAN

Бренд: Digi Страницы: 3

Бренд: Digi Страницы: 13

Бренд: Westermo Страницы: 20

Бренд: D-Link Страницы: 159

Бренд: D-Link Страницы: 169

Бренд: D-Link Страницы: 32

Бренд: Honeywell Страницы: 29

Бренд: Honeywell Страницы: 60

Wireless Communication Card

Бренд: Honeywell Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды