D-Link DES-3010F Скачать руководство пользователя

Страница: 74 / 187

DES-3000 Series Layer 2 Switch CLI Reference Manual

OOPBACK

ETECTION

OMMANDS

The Loopback Detection commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in
the following table.

Command Parameters

enable loopdetect

disable loopdetect

config loopdetect

[recover_timer [0 | <value 60-1000000>] | interval <value 1-32767>]

show loopdetect

config loopdetect ports

[<portlist> | all] state [enable | disable]

show loopdetect ports {<portlist>}

Each command is listed, in detail, in the following sections.

enable loopdetect

Purpose

Used to globally enable the Loopback Detection function on the
switch.

Syntax

enable loopdetect

Description

This command, along with the

disable loopdetect

command will

enable and disable the Loopback Detection function on the switch,
without adjusting configurations.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To enable the Loopback Detection function, globally, on the Switch:

DES-3026:4#enable loopdetect
Command: enable loopdetect

Success.

DES-3026:4#

disable loopdetect

Purpose

Used to globally disable the Loopback Detection function on the
switch.

Syntax

disable loopdetect

Description

This command, along with the

enable loopdetect

command will

enable and disable the Loopback Detection function on the switch,
without adjusting configurations.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable the Loopback Detection function, globally, on the Switch:

Содержание DES-3010F




























































































































































































Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды

D-Link DES-3010F, Руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды