D-Link DES-3010F Скачать руководство пользователя

Страница: 171 / 187

DES-3000 Series Layer 2 Switch CLI Reference Manual

System 10.90.90.90 00-01-02-03-04-00 Local
System 10.255.255.255 FF-FF-FF-FF-FF-FF Local/Broadcast

DES-3026:4#

Total Entries = 20

config arp_aging time

Purpose

Used to configure the age-out timer for ARP table entries on the Switch.

Syntax

config arp_aging time <value 0-65535>

Description

This command sets the maximum amount of time, in minutes, that an
ARP entry can remain in the Switch’s ARP table, without being
accessed, before it is dropped from the table.

Parameters

time <value 0-65535>

−

The ARP age-out time, in minutes. The value

may be set in the range of 0-65535 minutes with a default setting of 20
minutes.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure ARP aging time:

DES-3026:4#config arp_aging time 30
Command: config arp_aging time 30

Success.

DES-3026:4#

clear arptable

Purpose

Used to remove all dynamic ARP table entries.

Syntax

clear arptable

Description

This command is used to remove dynamic ARP table entries from
the Switch’s ARP table. Static ARP table entries are not affected.

Parameters None.

Only

administrator-level users can issue this command.

Restrictions

Example Usage:

To remove dynamic entries in the ARP table:

DES-3026:4#clear arptable
Command: clear arptable

Success.

DES-3026:4#

169

Содержание DES-3010F




























































































































































































Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды

D-Link DES-3010F, Руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3010F

Отзывы:

Похожие инструкции для DES-3010F

Бренды по названию

Популярные бренды