Curtis Instruments MultiMode 1243 Generation 2 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 90

background image

Curtis 1243

GEN

2 Manual

8

2 — INSTALLATION & WIRING:

Controller

Standard Power Wiring

Motor armature wiring is straightforward, with the armature

’

s A1 connection

going to the controller

’

s

B+

bus bar and the armature

’

s A2 connection going to

the controller

’

s

M-

bus bar.

The motor

’

s

fi

eld connections (S1 and S2) are less obvious. The direction

of vehicle travel with the forward direction selected will depend on how the
motor

’

s S1 and S2 connections are made to the controller

’

s two

fi

eld terminals

(

S1

and

S2

) and how the motor shaft is connected to the drive wheels through

the vehicle

’

s drive train.

CAUTION:

The polarity of the

S1

and

S2

connections

will affect the operation of the emergency reverse feature. The forward and
reverse switches and the

S1

and

S2

connections must be con

fi

gured so that the

vehicle drives away from the operator when the emergency reverse button is
pressed.

Standard Control Wiring

Wiring for the input switches and contactors is shown in Figure 3; the pins are
identi

fi

ed on page 6. In the standard wiring con

fi

guration, the auxiliary driver

at Pin 8 is used to drive an electromagnetic brake.

The main contactor coil must be wired directly to the controller as shown

in Figure 3. The controller checks for welded or missing contactor faults and
uses the main contactor coil driver output to disconnect the battery from the
controller and motor when speci

fi

c faults are present. If the main contactor coil

is not wired to Pin 4, the controller will not be able to open the main contactor
in serious fault conditions and the system will therefore not meet EEC safety
requirements.

☞

C A U T I O N

«
...
13
14
15
16
17
...
»

Содержание MultiMode 1243 Generation 2



























































































Отзывы:

Нет отзывов

Похожие инструкции для MultiMode 1243 Generation 2

Бренд: Vacon Страницы: 62

Бренд: Faber Страницы: 8

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: ZKTeco Страницы: 8

Бренд: EasyIO Страницы: 18

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Flashlight Blue

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 4

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 5

Бренд: I-Tork Страницы: 15

Бренд: MGC Страницы: 16

Extinguishing Control Panel BC06-2EXT

Бренд: LST Страницы: 4

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды