Curtis Instruments MultiMode 1243 Generation 2 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 90

background image

Curtis 1243

GEN

2 Manual

43

momentarily cycled during operation. However, it is important to bear in mind
that the same sequencing delay also delays the initiation of interlock braking (see
Figure 14, page 29).

The sequencing delay can be programmed from 0.0 to 3.0 seconds, with

0.0 corresponding to no delay.

The polarity of the

S1

and

S2

connections will affect the operation of the emergency

reverse feature. The forward and reverse switches and the

S1

and

S2

connections must

be configured so that the vehicle drives away from the operator when the emergency
reverse button is pressed.

EMR REV C/L

When emergency reverse is activated, the

emergency reverse current limit

parameter de

fi

nes the maximum braking current during deceleration and the

maximum drive current after the vehicle switches direction. The emergency
reverse current limit is adjustable from 50 amps up to the controller

’

s full rated

braking current. (The full rated braking current depends on the controller
model; see speci

fi

cations in Table D-1).

EMR REV CHECK

The

emergency reverse check

parameter is applicable only when the emergency

reverse feature is being used in the application. If emergency reverse is not being
used, this parameter should be set to Off.

When enabled (programmed On), the emergency reverse check tests for

continuity from the emergency reverse check output (Pin 10) to the emergency
reverse input (Pin 13). Therefore, the emergency reverse wiring should be
connected as closely as possible to the controller side of the emergency reverse
switch. The recommended wiring is shown in the standard wiring diagram,
Figure 3 (page 7).

EMR DIR INTR

In applications that use the emergency reverse feature, the

emergency reverse

direction interlock

parameter de

fi

nes the requirements for resuming normal

operation after using emergency reverse. After emergency reverse has been used,
the controller sets the output drive to zero regardless of whether a direction or
throttle is being requested. With the emergency reverse direction interlock
parameter set to On, the operator can either open both direction switches or
cycle the interlock switch to enable normal operation. With the emergency
reverse direction interlock parameter set to Off, the only way for the operator
to resume normal operation is by cycling the interlock switch.

3 — PROGRAMMABLE PARAMETERS:

Emergency Reverse Parameters

Emergency Reverse Parameters

☞

C A U T I O N

«
...
48
49
50
51
52
...
»

Содержание MultiMode 1243 Generation 2



























































































Отзывы:

Нет отзывов

Похожие инструкции для MultiMode 1243 Generation 2

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: QCON Страницы: 4

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 12

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 96

Бренд: asalvo Страницы: 46

Бренд: Sartorius Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды