Curtis Instruments MultiMode 1243 Generation 2 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 90

background image

Curtis 1243

GEN

2 Manual

47

3 — PROGRAMMABLE PARAMETERS:

Hourmeters

Setting the parameter to 0 means that the traction disable timer will never

expire and therefore never invoke the traction fault speed.

TRAC FAULT SPD

The

traction fault speed

parameter sets the maximum drive speed in the event

the traction disable timer expires or the total disable timer expires; it can be
adjusted between 0

–

100% of drive output, and applies to all modes.

The hourmeter service timers must be reset (programmed Off ) after service is
performed, using the Service Total and Service Traction parameters.

Occasionally, the vehicle may be brought in for servicing before its scheduled

maintenance is due—for example, because of some specific problem. You might want
to check the service timers at this time to see how many hours they have accumulated.
If routine maintenances is due shortly, you could perform it now instead, and reset
the appropriate service timer—thus avoiding an extra trip to the shop.

SERVICE TOTL

When the total service timer expires, the controller automatically sets the

service total

parameter On. The Service Total parameter must then be pro-

grammed Off to indicate the appropriate service has been performed.

If a vehicle is brought in for service before a service warning is issued, you

can check the accumulated total service hours. Plug in the 1311 programmer
and go to the Monitor menu. Multiply the

“

Tot Srvc X25

”

value by 25 and add

the

“

+Tot Srvc

”

value; this is how many total hours have elapsed since the total

service timer was last reset.

When service is performed before the total service timer expires, the

Service Total parameter must be programmed On and then Off to reset it.

SERVICE TRAC

When the traction service timer expires, the controller automatically sets the

service traction

parameter On. The Service Traction parameter must then be

programmed Off to indicate the appropriate service has been performed.

If a vehicle is brought in for service before a service warning is issued, you

can check the accumulated traction service hours. Plug in the 1311 program-
mer and go to the Monitor menu. Multiply the

“

Trac Srvc X25

”

value by 25

and add the

“

+Trac Srvc

”

value; this is how many traction hours have elapsed

since the traction service timer was last reset.

When service is performed before the traction service timer expires, the

Service Traction parameter must be programmed On and then Off to reset it.

Hourmeter Service Timer Resetting

«
...
52
53
54
55
56
...
»

Содержание MultiMode 1243 Generation 2



























































































Отзывы:

Нет отзывов

Похожие инструкции для MultiMode 1243 Generation 2

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: Samson Страницы: 2

M16/RM N.C. DN 65 EEX

Бренд: Madas Страницы: 44

Бренд: York Страницы: 20

Бренд: Patron Страницы: 17

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Бренд: Combi Страницы: 16

RM-LUM-M320-IT/A

Бренд: Grosvenor Страницы: 2

Calc-An-Acre II

Бренд: micro-trak Страницы: 30

Ecomat100 CR1055

Бренд: IFM Страницы: 32

Бренд: Chamberlain Страницы: 4

Бренд: Shimaden Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды