Curtis Instruments MultiMode 1243 Generation 2 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 90

background image

Curtis 1243

GEN

2 Manual

58

5 — VEHICLE PERFORMANCE ADJUSTMENT

2

Tuning the Controller to the Motor

The 1243

GEN

2 controller has the flexibility to be tuned to nearly any separately

excited motor from any manufacturer. The programmable parameters allow full
control of the motor

’

s maximum armature current during driving and braking

and full control of the motor

’

s maximum and minimum

fi

eld current as well as

the

fi

eld current relationship to the armature current. This flexibility allows

motor performance to be maximized while protecting it from operating outside
its safe commutation region.

In order to properly tune the controller, the following information should

be obtained from the motor manufacturer:

•

MAXIMUM ARMATURE CURRENT RATING

•

MAXIMUM FIELD CURRENT RATING

•

MINIMUM FIELD CURRENT RATING

•

FIELD RESISTANCE

,

HOT AND COLD

.

The performance of a separately excited motor changes depending on tempera-
ture. This is due to the change in

fi

eld winding resistance as the motor heats up

through use. When the

fi

eld winding temperature increases, so does its resis-

tance; therefore, the maximum current that can be forced through the winding
is reduced. Reductions in the

fi

eld current over the motor

’

s typical operating

temperature range can be 10% to 50%. Since the maximum available

fi

eld

current determines the maximum torque that can be produced by the motor, the
vehicle

’

s performance under load and up inclines will change as the motor heats

up. The change in performance can be limited by tuning the motor when it is
hot rather than cold. Therefore, it is recommended that the following procedure
be performed with a hot motor.

STEP

1. Using the programmer

’

s Program Menu, set the Drive Current

Limit parameter value in each mode to the smaller of: (a) the
motor

’

s peak armature current rating, or (b) the maximum

controller drive current limit. This value can later be adjusted to
establish the desired vehicle driving feel in each mode.

STEP

2. Set the Braking Current Limit parameter value in each mode to

the smaller of: (a) the maximum motor armature current rating,
or (b) the maximum controller braking current limit. This value
can later be adjusted to establish the desired vehicle braking feel
in each mode.

STEP

3. To set the Field Max parameter value,

fi

rst decide whether you

want to maintain consistent vehicle operation throughout the
motor

’

s temperature range. If you do, proceed to Step 4. If,

however, maintaining operational consistency across motor tem-
perature is not a concern, but achieving maximum torque is,
proceed to Step 5.

STEP

4. For the most consistent operation across temperature, set the

Field Max parameter to the maximum

fi

eld current available at

«
...
63
64
65
66
67
...
»

Содержание MultiMode 1243 Generation 2



























































































Отзывы:

Нет отзывов

Похожие инструкции для MultiMode 1243 Generation 2

Бренд: Eaton Страницы: 50

Бренд: Jafar Страницы: 10

Бренд: Badger Basket Страницы: 3

Бренд: BADLANDS Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: GCE Страницы: 24

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

Бренд: Elby Designs Страницы: 4

Бренд: Comet Страницы: 9

Бренд: Harman Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Nortek Страницы: 24

Бренд: Contemporary Research Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды