Crystal Vision Indigo DT Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 47

background image

Crystal Vision

Installation

2 Installation

2.1 General Safety Summary

The following warnings are intended for user guidance and safety.

Ground

This product must be grounded through the grounding
conductor of the power cord.

Power cable

Use only a power cord that meets the required specification for
this product.

Fuses

To avoid fire hazard use only fuses of the type and rating
specified.

Service

These servicing instructions are for use by qualified personnel
only. To reduce risk of electric shock, do not perform any
servicing other than that contained in this manual unless you
are qualified to do so. Refer all servicing to qualified service
personnel.

Apart from procedures described in this manual there are no
user serviceable parts within the frame. If the frame requires
any other servicing it should be returned to the manufacturer or
dealer.

On no account should the unit be powered whilst any covers
are removed.

Ventilation

The unit must have adequate ventilation. The left and right
ventilation grilles must not be obstructed. If installed in a
standard 19" rack, cool air circulation should be available.

EMC

To comply with EMC regulations the following guidelines
should be observed:

Do not operate this unit for extended periods with the front
panel open.

Do not use the frame unless all the rear connector positions
are filled, either with Crystal Vision rear modules, or with
Crystal Vision blanking plates.

Do not operate the equipment with covers or panels removed.

General

To avoid electric shock do not operate this product in wet or
damp conditions.

To avoid injury or fire hazard do not operate this product in an
explosive atmosphere.

Only use this rack in conjunction with Crystal Vision modules
designed for that purpose.

Indigo DT User Manual R1.8

5

05 July 2018

«
...
4
5
6
7
8
...
»

Содержание Indigo DT
















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo DT

Бренд: Omnia Страницы: 102

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 74

Бренд: 3Com Страницы: 6

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: Commell Страницы: 36

Бренд: Edge-Core Страницы: 7

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

Бренд: FOR-A Страницы: 39

Бренд: Delta Electronics Страницы: 1

Бренд: UNA AUTOMATION Страницы: 20

Бренд: Renesas Страницы: 76

Бренд: ASROCK Страницы: 173

Бренд: Rosewill Страницы: 2

Advanced Flame 1.0

Бренд: Eastern Voltage Research Страницы: 12

Бренд: ADTRAN Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды