Crystal Vision Indigo DT Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 47

background image

Crystal Vision

Installation

Description

Data

Flashing

This LED will flash to indicate activity.

Link

Normally lit

This LED will be lit whenever the frame is connected to an
Ethernet network.

Piano Switches

Switches 1 and 2 configure the cooling fan modes.

Levers 1 &2

Function

Notes

Both up

Normal
cooling

Both fans run continuously, increasing in speed as the
temperature inside the frame goes up.

1 down, 2 up

Quiet mode

For use with a lightly loaded frame for low ambient temperature.
When the frame temperature is below approximately 45°C the
panel fan is switched off and the PSU fan runs at minimum
speed. If the frame temperature goes above 45°C it reverts to
normal cooling and goes back to quiet mode when frame
temperature falls below 42°C.

1 up, 2 down

Max cooling
mode

In Maximum cooling mode both fans never run below near
maximum speed. Fan speed increases to maximum at high
frame temperature. This mode is ideal for equipment bays
where noise is not a concern.

Both down

Reserved for
future use

Operates as normal mode with current software.

Slide switches

Switch

Function

Notes

1

Debug

Normally right, no user function.

2

Default IP
address

Normally right, left set IP address to default 10.0.0.201.

3

Normally right, no user function.

422 Term

Terminates RS422 input – no longer supported.

Upper/Lower

No user function – leave set to ‘Lower’.

Note:

Quiet mode is dependent on PSU and PSU fans not being in an alarm state.
If one of the fans should fail, the closed frame can still operate indefinitely with
an ambient temperature of up to 40°C.
Although only one of the fans is essential in normal operation, a faulty fan
should be replaced as soon as practical to prevent the long-term stressing of the
modules.

Warning:

Although it is possible to operate the frame with the front panel open, the frame
may not meet electromagnetic compatibility (EMC) requirements in this
condition.

Indigo DT User Manual R1.8

10

05 July 2018

«
...
9
10
11
12
13
...
»

Содержание Indigo DT
















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo DT

PCMCIA WIRELESS ASAPTER DWL-650

Бренд: D-Link Страницы: 5

PowerLine DHP-W611AV

Бренд: D-Link Страницы: 78

Бренд: Sangoma Страницы: 6

Бренд: Quatech Страницы: 27

Бренд: Yaesu Страницы: 2

Бренд: Alesis Страницы: 61

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

Бренд: QNAP Страницы: 54

Бренд: axing Страницы: 4

TeleCLIENT TC7730 Series

Бренд: ETL Страницы: 83

Бренд: Arduino Страницы: 25

SRA311-008P8 Series

Бренд: Divio Страницы: 4

Бренд: Renesas Страницы: 76

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Бренд: Xantech Страницы: 16

Бренд: ETAS Страницы: 84

Бренд: Flexwatch Страницы: 13

Бренд: Matrix Switch Corporation Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды