Crystal Vision Indigo DT Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 47

background image

Crystal Vision

Appendix 2

MIB tree

Object identifiers (OID)

For each variable to be monitored there is an object identifier or OID which can be
distinguished from any other OID within the MIB by its unique bit number.

As an example, the Front panel open status for the frame with slot addresses set to
Lower (See section 2.4 for an explanation of slot addresses) is recorded by the OID
1.3.6.1.4.28681.

1

.2.1.

5

.

1

where

1

is the board type (Frame), the

5

is the bit number

(Frame open) and the final

1

indicates that the frame slot addresses is set to lower.

If the frame was set to upper slot addressing the OID would be
1.3.6.4.28681.

1

.2.1.5.

2

. The OID will then be accompanied by a value to indicate its

status. Any status change will cause the transmitting of a trap to the SNMP
manager.

Note:

The SNMP monitor allows for two frames to be connected as a frame pair. The
second frame will be reported as Unknown when not present.

The frame variables monitored are:

Name

Value

Name

Value

Frame Present 1

Frame PIC found/not found

PSU Present 1

Found/not yet found

Frame Present 2

Frame PIC found/not found

PSU Present 2

Found/not yet found

Frame Type 1

Reserved/unknown

PSU Present 3

Found/not yet found

Frame Type 2

Reserved/unknown

PSU Present 4

Found/not yet found

Frame Temperature 1

Integer (temp)

PSU Type 1

PSU-160i/unknown

Frame Temperature 2

Integer (0)

PSU Type 2

PSU-160i/unknown

Frame Open 1

Front panel
open/closed/unknown

PSU Type 3

PSU-160i/unknown

Frame Open 2

Front panel
open/closed/unknown

PSU Type 4

PSU-160i/unknown

Frame PSU Fan Status
1

PSU fan
OK/problem/unknown

PSU Status 1

PSU
OK/problem/unknown

Frame PSU Fan Status
2

PSU fan
OK/problem/unknown

PSU Status 2

PSU
OK/problem/unknown

Frame Panel Fan Status
1

Panel fan
OK/problem/unknown

PSU Status 3

PSU
OK/problem/unknown

Frame Panel Fan Status
2

Panel fan
OK/problem/unknown

PSU Status 4

PSU
OK/problem/unknown

Frame Temperature
Alarm 1

Frame temperature OK/too
high/unknown

Expected but not
fitted PSU

PSU not fitted or not
powered

Frame Temperature
Alarm 2

Frame temperature OK/too
high/unknown

Indigo DT User Manual R1.8

40

05 July 2018

«
...
39
40
41
42
43
...
»

Содержание Indigo DT
















































Отзывы:

Нет отзывов

Похожие инструкции для Indigo DT

Бренд: Keithley Страницы: 59

Бренд: Salto Страницы: 2

Бренд: Idis Страницы: 86

Бренд: Paradyne Страницы: 2

Бренд: Delta Electronics Страницы: 1

Бренд: Tandy Страницы: 24

Бренд: Galaxy Страницы: 30

EK-FC750 GTX Series

Бренд: ekwb Страницы: 2

Бренд: WTI Страницы: 178

Бренд: ZALMAN Страницы: 6

Бренд: Devolo Страницы: 24

Бренд: Ericsson Страницы: 16

Бренд: Fujitsu Страницы: 14

Aaeon UPN Edge Pro

Бренд: Asus Страницы: 55

Бренд: Asus Страницы: 24

Бренд: Asus Страницы: 17

Бренд: Asus Страницы: 21

Бренд: Asus Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды