Crary CWS CASE IH 2162 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 92

Crary CWS CASE IH 2162 Скачать руководство пользователя страница 9

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

1

INTRODUCTION

Section

1

Congratulations on your choice of a new Crary Wind System
(CWS) to complement your farming operation. This equip-
ment has been designed and manufactured to meet the
needs of a discerning agricultural industry for the eﬃ cient
harvesting of crops.

Safe,  eﬃ  cient,  and  trouble  free  operation  of  your  CWS
requires that you and anyone else who will be operating or
maintaining the machine, read and understand the Safety,
Operation,  Maintenance,  and  Trouble  Shooting  informa-
tion contained within the Operator’s Manual. Check each
item referred to and acquaint yourself with the adjustments
required to obtain eﬃ  cient operation.

This manual covers all the CWS models manufactured by
Crary Industries for MacDon FD1, MacDon FD70, MacDon
FD75, and Case IH 2162 headers. Use the table of contents
as a guide to locate required information.

Keep this manual handy for frequent reference and to pass
on to new operators or owners. Call your Crary dealer or
distributor if you need assistance, information, or additional
copies of the manuals.

OPERATOR ORIENTATION -

All references to left, right, front and rear of the machine, as mentioned throughout the

manual, are determined by standing behind the machine and facing towards the direction of forward travel.

Many people have worked on the design, production, and
delivery of this machine. They have built into it the highest
quality of materials and workmanship. The information in this
manual is based on the knowledge, study, and experience
of these people through years of manufacturing specialized
farming machinery.

The performance of the machine depends on proper main-
tenance and adjustment. Even if you are an experienced
operator of this or similar equipment, we ask you to read
the operator’s manual before running the machine. Keep
the manual handy for future reference. It has been carefully
prepared, organized, and illustrated to assist you in ﬁ nding
the information you need. Your Crary dealer will be happy
to answer any further questions you may have about the
machine.

«
...
7
8
9
10
11
...
»

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов