Crary CWS CASE IH 2162 Скачать руководство пользователя страница 26

Страница: 26 / 92

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

ASSEMBLY

4.4.2 CENTER MOUNT

1. Remove the existing OEM cylinder mount from the front

of the reel arm and discard.

2. Use a 3/8 x 4-1/2” bolt and nylock nut to secure the

3-1/8” nylon bearing to the center reel mount base.
Nylon bearing should rotate freely

3. Slide the center reel mount onto the OEM reel arm.

Attach the bottom of the center reel mount to the OEM
reel arm using a 1/2” x 1-1/4” bolt and nut. (Figure 17)

4. Attach the lock bracket to the center reel mount with

two 1/2” x 1-1/4” bolts. The lock bracket should be
adjusted to securely clamp the center reel mount to
the OEM reel mount.

5. Attach the arm mount to the center reel mount using

two 1/2” x 4-1/2” bolts and nylock nuts.

6. Insert the center reel mount into the arm mount and

secure with a 1/2” x 2-3/4” bolt and 1/2” nylock nut.

7. Install new cylinder mount using four 1/2” x 1” Torx bolts.

8. Attach the cylinder to the cylinder mount with the

provided cylinder pin and two hair pins.

CAUTION

Be sure the reel is secure and will not move before be-
ginning installation.

4.4 REEL ARM MOUNT (FD1 & FD75 HEADERS)

Figure 16: Center reel mount (FD75 headers)

Содержание CWS CASE IH 2162





























































































Результаты поиска

Содержание CWS CASE IH 2162

Отзывы:

Crary CWS CASE IH 2162, Руководство пользователя и каталог запчастей, Страница: 26 / 92

Результаты поиска

Содержание CWS CASE IH 2162

Отзывы: