Crary CWS CASE IH 2162 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 92

Crary CWS CASE IH 2162 Скачать руководство пользователя страница 12

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

4

SAFETY

1. Follow ALL operating, maintenance, and safety informa-

tion in this manual.

2. Support the machine with blocks or safety stands when

working around it.

3. Follow good shop practices:

• Keep service area clean

and dry.

• Be sure electrical outlets

and tools are properly
grounded.

• Use adequate light for the

job at hand.

4. Use only tools, jacks and hoists of sufficient capacity

for the job.

5. Place all controls in neutral or off, lower header to the

ground, stop combine engine, set parking brake, chock
wheels, remove ignition key and wait for all moving
parts to stop before servicing, adjusting, repairing or
unplugging.

6. When maintenance work is completed, install and se-

cure all guards before resuming work.

7. Relieve pressure from hydraulic circuit before servicing

or disconnecting from combine.

8. Keep hands, feet, hair and clothing away from all mov-

ing and/or rotating parts.

9. Clear the area of bystanders, especially small children,

when carrying out any maintenance and repairs or mak-
ing any adjustments.

10. Keep safety decals clean. Replace any decal that is

damaged or not clearly visible.

11. First-class maintenance is a prerequisite for the safest

operation of your machine. Maintenance, including
lubrications, should be performed with the machine
stopped and locked out.

1. Read and understand the Owner’s Manual and all

safety decals before servicing, adjusting or repairing.

2. Install and secure all guards and shields before starting

or operating.

3. Keep hands, feet, hair and clothing away from all mov-

ing and/or rotating parts.

4. Place all controls in neutral or off, lower header to the

ground, stop combine engine, set parking brake, chock
wheels, remove ignition key and wait for all moving
parts to stop before servicing, adjusting, repairing or
unplugging.

5. Clear the area of bystanders, especially small children,

before starting.

6. Keep all hydraulic lines, fittings, and couplers tight and

free of leaks before and during use.

7. Clean reflectors and lights before transporting.

8. Review safety related items annually with all person-

nel who will be operating or maintaining the machine.

9. Shut the combine off when connecting the machine

hydraulics.

10. Do not exceed fan speed of 5300 RPM. Check the fan

speed by multiplying the driveline speed (RPM) by the
gear ratio of the gearbox.

11. Do not run the fan without back pressure. Close the

butterfly valve on the fan if the flex hose is disconnected.

Think SAFETY! Work SAFELY!

2.3 OPERATING SAFETY

2.4 MAINTENANCE SAFETY

«
...
10
11
12
13
14
...
»

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов