Crary CWS CASE IH 2162 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 92

Crary CWS CASE IH 2162 Скачать руководство пользователя страница 10

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

2

Section

SAFETY

2

2.1 SAFETY ALERT SYMBOL

DANGER -

Indicates an imminently hazardous situation

that, if not avoided, will result in death or serious injury.
This signal word is to be limited to the most extreme
situations, typically for ma chine components that, for
functional purposes, cannot be guarded.

WARNING-

Indicates a potentially hazardous situation

that,  if  not  avoided,  could  result  in  death  or  serious
injury,  and  includes  hazards  that  are  exposed  when
guards  are  removed.    It  may  also  be  used  to  alert
against unsafe prac tices.

CAUTION -

Indicates a potentially hazardous situation

that, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe
practices.

IMPORTANT-

Instructions that must be followed to

ensure proper installation/operation of equipment.

NOTE -

General statements to assist the reader.

This Safety Alert Symbol means:

ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED!

The Safety Alert symbol identiﬁ es important
safety messages on the machine and in the
manual. When you see this symbol, be
alert to the possibility of personal injury or
death. Follow the instructions in the safety
message.

Why is SAFETY important to you?

1. Accidents Disable and Kill

2. Accidents Cost

3. Accidents Can Be Avoided

SIGNAL WORDS:

Note the use of the signal words

DANGER

,

WARNING

,

CAUTION, IMPORTANT

and

NOTE

with the safety

messages. The appropriate signal word for each mes-
sage has been selected using the following guidelines:

3 Big Reasons

«
...
8
9
10
11
12
...
»

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов