manualshive.com logo in svg

Crary CWS CASE IH 2162, Руководство пользователя и каталог запчастей, Страница: 11 / 92

Поделиться
Скачать
Crary CWS CASE IH 2162 Скачать руководство пользователя страница 11

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

3

SAFETY

YOU

 are responsible for the 

SAFE

 operation and mainte-

nance of your machine. You must ensure that you and any-
one else who is going to operate, maintain or work around 
the machine are familiar with the operat ing and maintenance 
procedures and related safety information contained in this 
manual. This manual will alert you to all good safety prac-
tices that should be adhered to while operat ing the machine.

Remember, 

YOU

 are the key to safety. Good safety prac-

tices not only protect you but also the people around you. 
Make these practices a working part of your safety program. 
Be  certain  that 

EVERYONE

  operating  this  equipment  is 

familiar with the recommended operating and maintenance 
procedures  and  follows  all  the  safety  precautions.  Most 
accidents can be prevented. Do not risk injury or death by 
ignoring good safety practices.

•  Owners must give operating instruc tions to opera-

tors or employees before allowing them to operate 
the  machine,  and  annually  thereafter  per  OSHA 
(Occupational Safety and Health Administration) 
regulation 1928.57.

•  The most important safety device on this equipment 

is a safe operator. It is the operator’s responsibility 
to read and under stand all Safety and Operating 
instructions in the manual and to follow them. All 
acci dents can be avoided.

•  A  person  who  has  not  read  and  understood  all 

operating and safety instructions is not qualified 
to  operate  the  machine.   An  untrained  operator 
exposes himself and bystanders to possible seri-
ous injury or death.

•  Do not modify the equipment in anyway. Unauthor-

ized modification may impair the function and/or 
safety and could affect the life of the equipment.

1.  Read  and  understand  the 

Owner’s  Manual  and  all 
safety decals before operat-
ing, maintaining, adjusting or 
servicing the machine.

2.  Only  trained  persons  shall 

operate  the  machine.    An 
untrained  operator  is  not 
qualified to operate the machine.

3.  Have a first-aid kit available for use, 

should the need arise, and know how 
to use it.

4.  Provide  a  fire  extinguisher  for  use  in 

case of an accident.  Store in a highly 
visible place.

5.  Do not allow children, spectators or by-

standers within hazard area of machine.

6.  Wear appropriate protective gear.  This 

list includes but is not limited to:

•  A hard hat.

•  Protective  shoes  with  slip 

resistant soles.

•  Protective goggles.

•  Heavy gloves.

•  Hearing protection.

•  Respirator or filter mask.

7.  Wear suitable ear protection during 

prolonged  exposure  to  excessive 
noise.

8.  Place  all  controls  in  neutral  or  off, 

lower  header  to  the  ground,  stop 
combine engine, set parking brake, chock wheels, re-
move ignition key and wait for all moving parts to stop, 
before servicing, adjusting, repairing or unplugging.

9.  Review safety related items annually with all personnel 

who will be operating or maintain ing the machine.

Think SAFETY! Work SAFELY!

2.2   GENERAL SAFETY

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов