manualshive.com logo in svg

Crary CWS CASE IH 2162, Руководство пользователя и каталог запчастей, Страница: 2 / 92

Поделиться
Скачать
Crary CWS CASE IH 2162 Скачать руководство пользователя страница 2

© 2018, Crary Industries,  All rights reserved.  Produced and printed in the USA.

HOW TO REACH US

ADDRESS

HOURS

TELEPHONE

FAX NUMBER

E-MAIL

INTERNET

Crary Industries, Inc.

237 12

th

 St. NW

West Fargo, ND 58078

Monday-Friday      

8 am-5pm (CST)

For Parts and Service:

Ph: 701.282.5520 • 

800.247.7335

Fax: 701.282.9522

Email: [email protected] • 

[email protected]

Online: www.crary.com

DISCLAIMER

This document is based on information available at the time of its publication.  While efforts have been made to be accurate, the 
information contained herein does not purport to cover all details or variations, nor to provide for every possible contingency in con-
nection with installation, operation, or maintenance.  Features may be described herein which are not present in all systems.  Crary 
Industries assumes no obligation of notice to holders of this document with respect to changes subsequently made.

Crary Industries assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein.

MANUFACTURED BY CRARY INDUSTRIES

MANUFACTURED IN U.S.A.

XXXXXX

WEST FARGO, NORTH DAKOTA 58078 U.S.A.

SERIAL NUMBER

Serial Number Decal

CWS MANIFOLD

SERIAL NUMBER DECAL

Serial number location

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE.

.

THE CRARY INDUSTRIES STATEMENT OF PRODUCT SAFETY

As a manufacturer of specialized agricultural equipment, Crary Industries fully recognizes its responsibility of providing its customers 
products that perform their expected use in a reasonably safe manner.  Safety considerations shall be an integral and high prior-
ity part of all engineering/design analysis and judgments involving Crary products.  It is our stated policy that our products will be 
manufactured to comply with the safety standards specified by the American Society of Agricultural Engineers, the National Electrical 
Code, the Society of Automotive Engineers, and/or any other applicable recognized standards at the time manufactured.  However, 
this statement should not be construed to mean that our product will safeguard against a customer’s own carelessness or neglect in 
violating common safety practices specified in each product’s manual, nor will we be liable for any such act.

SERIAL NUMBER LOCATION

Always give your authorized Crary dealer the serial number of your machine when ordering parts, requesting service, or any other 
information. The serial number decal is located on the front, left hand end of the air manifold, as shown below.

Please record the serial number in the space provided on the front cover and on the warranty and registration card.

Crary Industries is continually making improvements and developing new equipment.  In doing so, we reserve 
the right to make changes or add improvements to our product without obligation for equipment previously 
sold. For the latest product manual, please go to www.crary.com/Product-Support/Find-A-Product-Manual.

Because modification to this machine may affect the performance, function, and safety of its operation, no 
modifications are to be made without the written permission of Crary Industries.  Part replacements should 
be with original equipment supplied by Crary Industries.

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов