manualshive.com logo in svg

Crary CWS CASE IH 2162, Руководство пользователя и каталог запчастей, Страница: 39 / 92

Поделиться
Скачать
Crary CWS CASE IH 2162 Скачать руководство пользователя страница 39

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

31

ASSEMBLY

4.8   FLEX HOSE ROUTING 

For  easy  installation  of  hose  parts,  you  may  use  a 
solution  of  soap  and  water  as  lubricant  when  sliding 
hose pieces together.

NOTE

1.  Set the 56” aluminum side manifold on the side tube 

mount. Position the manifold so that the front end is 
about two inches from the front U-bolt.

2.  Fasten the manifold to the tube mount weldment with 

two 5/16” u-bolts and four nuts (Figure 42). 

3.  Slide an 8-11/16” t-bolt clamp over each end of the 90 

degree elbow. Then, slide the elbow over the RH end 
of the front CWS manifold. Point the elbow toward the 
rear manifold.

4.  Insert an elbow support band into the 90º elbow.

5.  Determine the length of hose needed to connect the 

elbow  support  band  to  the  56”  manifold  and  cut  the 
hose. Leave enough slack in this portion of flex hose 
to allow complete up/down and fore/aft movement of 
the reel.

6.  Install the flex hose over the elbow support band and 

the front end of the 56” manifold with two 8-3/8” t-bolt 
clamps.

7.  Slide an 8-11/16” t-bolt clamp over each end of a 90º 

elbow. Then, slide the elbow onto the fan outlet. Point 
the elbow toward the rear manifold.

8.  Insert an elbow support band into the elbow installed 

in the previous step.

9.  Determine the length of flex hose needed to connect 

the elbow support band to the RH rear manifold and cut 
the hose.  Install the flex hose over the elbow support 
band and the back end of the manifold with two 8-3/8” 
t-bolt clamps.

10.  Slide  an  8-11/16”  t-bolt  clamp  over  each  end  of  the 

45º elbow. Then, slide the elbow onto the RH end rear 
manifold. Point the elbow toward the 56” manifold on 
the side of the reel.

11.  Insert an elbow support band into the 45 degree elbow.
12.  Determine the length of flex hose needed to connect 

the elbow support band to the 56” manifold. Cut the 
hose  if  needed.  Leave  enough  slack  in  this  portion 
of  flex  hose  to  allow  complete  up/down  and  fore/aft 
movement of the reel.

4.8.1 RIGHT HAND ROUTING

NOTE

If installing dual fl ow system, Install alternate rubber-Y 
connection, see Figure 42.

13.  Install  the  flex  hose  on  the  elbow  support  band  and 

the rear end of the 56” manifold with two 8-3/8” t-bolt 
clamps.

14.  Tighten  all  t-bolt  clamps  to  the  torque  specifications 

on page 48.

 4.8.2 LEFT HAND ROUTING

1.  Secure the transition tube mount brackets to the fluid 

reservoir  on  the  back  of  the  header  using  four  set 
screws.  Place the tube mount as shown in Figure 43 
on  page  page  33.    For  FD70  or  CIH  2162,  the  right 
transition  tube  mount  bracket  should  have  been  in-
stalled at the same time as the gearbox mount bracket.

2.  Refer to Figure 9 and Figure 46 dimension A for tube 

mount location and orientation.  Using a mount clamp 
as a template, measure from the left hand inside edge 
of the header and mark and drill two 9/32” holes.  Install 
the tube mount weldment using two 11/32 X 7/8” scews. 

3.  Refer to Figure 9 and Figure 46 dimension B for tube 

mount location and orientation.  Using a tube mount as 
a template, measure from the left hand inside edge of 
the header and mark and drill two 9/32” holes.  Install 
the tube mount weldment using two 11/32 X 7/8” screws.  

4.  Set the 141” center manifold on the tube mounts over 

the feeder house and secure each end with a u-bolt 
and two 5/16” nuts and washers.  Position as shown 
in  Figure 45.

Two  sets  of  tube  mounts  are  provided  for  the  center 
manifold.    Use  the  tube  mounts  with  the  slotted  hole 
(reference purposes only) when installing on an FD70.  
Use  the  tube  mounts  without  the  slotted  hole  when 
installing on an FD1 or FD75.  Discard the tube mounts 
that are not used.

NOTE

IMPORTANT

DO NOT drill into the fl uid reservoir.  Tighten bolts on the 
clamp so that they secure the clamp around the reservoir.

5.  Determine the length of hose needed to connect the 

rubber-”Y” and the center manifold. After determining 
the length of hose needed, cut the hose.

IMPORTANT

On FD70 for Gleaner or Lexion combines only:

  To 

prevent damage to the cab when fully raising the head, 
the tube mount kit on page 82 is required to relocate the 
center dual fl ow tube that passes over the feederhouse. 
Use the FD1 & FD75 dimensions in Figure 43 or similar 
to  locate  the  two  mounts.  Failure  to  do  so  may  cause 
damage to the cab.

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов