Crary CWS CASE IH 2162 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 92

Crary CWS CASE IH 2162 Скачать руководство пользователя страница 13

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

5

SAFETY

1. Always place all combine hydraulic controls in neutral

before disconnecting from combine or working on hy-
draulic system.

2. Make sure that all components in the hydraulic system

are kept in good condition and are clean.

3. Relieve pressure before working on the hydraulic

system.

4. Replace any worn, cut, abraded, flattened or crimped

hoses.

5. Do not attempt any makeshift repairs to the hydraulic

fittings or hoses by using tape, clamps or cements.
The hydraulic system operates under extremely high-
pressure. Such repairs will fail suddenly and create a
hazardous and unsafe condition.

6. Wear proper hand and eye protec-

tion  when  searching  for  a  high-
pressure  hydraulic  leak.    Use  a
piece  of  wood  or  cardboard  as
a  backstop  instead  of  hands  to
isolate and identify a leak.

7. If injured by a concentrated high-

pressure  stream  of  hydraulic
fluid,  seek  medical  attention  im-
mediately.    Serious  infection  or
toxic  reaction  can  develop  from
hydraulic fluid piercing the skin surface.

8. Before applying pressure to the system, make sure all

components are tight and that lines, hoses, and cou-
plings are not damaged.

Think SAFETY! Work SAFELY!

2.5 HYDRAULIC SAFETY

2.6 PTO SAFETY

1. Keep bystanders, especially children, away from

drivelines.

2. Be extremely careful when working around PTO shafts,

drivelines, or other rotating shafts.

3. Do not remove or modify protective shields or guards.

4. Do not step across a PTO shaft or driveline or use it

as a step.

5. Keep guards and shields in place at all times while

operating.

6. Replace all damaged or missing parts or shields with

the correct original manufacturer’s parts.

7. Grease, clean, and maintain PTO components ac-

cording to original manufacturer’s specifications and
information in this manual.

8. Clothing worn by the operator must be fairly tight.

Never wear loose-fitted jackets, shirts, or pants when
working around the drivelines. Tie long hair back or
put under a cap.

9. Keep hydraulic hoses, electrical cords, chains, and

other items from contacting the drivelines.

10. Do not clean, lubricate, or adjust the drivelines when

the reel is engaged and the combine is running.`

«
...
11
12
13
14
15
...
»

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов