manualshive.com logo in svg

Crary CWS CASE IH 2162, Руководство пользователя и каталог запчастей, Страница: 50 / 92

Поделиться
Скачать
Crary CWS CASE IH 2162 Скачать руководство пользователя страница 50

PN 50887-00   

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

42

OPERATION

5.6   OPERATING HINTS

The following are recommended adjustments the operator 
can make based on crop conditions.  Any adjustments that 
involve the operator leaving the combine cab should heed 
the warning instructions listed below.

1.  Increase air to maximum.

2.  Move tilt control until air is directed at back of sickle bar 

with reel feeding properly.

3.  Gradually  reduce  air  until  crop  is  no  longer  flowing 

smoothly across sickle.

4.  Gradually  increase  air  until  smooth  crop  flow  across 

the sickle is achieved.

5.  Remember: more air uses more horsepower.

6.  Gradually adjust air position fore and aft until optimum 

crop flow is achieved.

7.  Gradually reduce air further until minimum air is used 

to maintain crop flow.

5.7   TRANSPORTING

The CWS is designed to be easily and conveniently moved 
from location to location.  When transporting the  machine, 
review and follow these safety instructions:
1.  Make sure you are in compliance with all local regula-

tions  regarding transporting equipment on public roads 
and highways.

2.  It is the responsibility to the owner to know the light-

ing  and    marking  requirements  of  the  local  highway 
authorities and to install and maintain the equipment 
to provide compliance with the regulations.  Add extra 
lights when transporting at night or during periods of 
limited visibility.

3.  See the owner’s manual that came with your combine 

and  header for proper transportation guidelines.

DO USE AIR TO FEED CROP ACROSS THE SICKLE.

DO ADJUST AIR TUBE ANGLE TO MAXIMIZE CROP 
FLOW ACROSS THE SICKLE.

DO USE THE REEL TO BRING THE CROP TO THE 
HEADER.

DO MAKE ADJUSTMENTS GRADUALLY.

DO VERIFY PROPER AIR POSITION WHENEVER 
ADJUSTING  REEL  HEIGHT  OR  FORE AND AFT 
POSITION.

DO SHUT OFF AIR IMMEDIATELY IF THE AIR HOSE 
SHOULD FAIL.  FAILURE TO DO SO MAY RESULT 
IN GEARBOX FAILURE.

DO  FOLLOW  TROUBLESHOOTING  GUIDE  ONE 
STEP AT A TIME.

DO NOT USE MORE AIR THAN NEEDED.

DO NOT OPERATE WITH THE AIR TUBES ON THE 
GROUND.

DO NOT OPERATE WITH PLUGGED AIR TUBES.

DO  NOT  OPERATE  WITH  AIR  HOSE  DISCON-
NECTED.

Place all controls in neutral or off , stop combine engine, 
set  parking  brake,  remove  ignition  key,  wait  for  all 
moving  parts  to  stop,  then  properly  block  machine 
before servicing, adjusting, repairing, or unplugging.

WARNING

Содержание CWS CASE IH 2162





























































































Отзывы:

Нет отзывов