background image

A-1

APPENDIX

Limited Product Warranty

A

COULOMB TECHNOLOGIES INC.
LIMITED PRODUCT WARRANTY

This Limited Product Warranty applies to you, a customer who has purchased COULOMB’s ChargePoint™ Networked 
Charging Stations and/or related products (“

Products

”) from COULOMB TECHNOLOGIES, INC. (“

COULOMB

”) or one of its 

authorized distributors and not for resale. 

LIMITED ONE-YEAR WARRANTY

Subject to the exclusions from warranty coverage set forth below, COULOMB warrants that the Product will be free from 
any defects in materials and/or workmanship (the “

Limited Warranty

”) for a period of one (1) year after the date of the initial 

installation of the Product (the “

One-Year Warranty Period

”). If the Product becomes defective in breach of the Limited 

Warranty, COULOMB will, upon written notice of the defect received during the One-Year Warranty period, either repair or 
replace, at Coulomb’s election, the Product if it proves to be defective; 

provided

, that COULOMB will not be responsible for 

the cost of any labor associated with the repair or replacement of any defective Product.

FIVE-YEAR EXTENDED WARRANTY (Additional Charge Applies)

Subject to the exclusions from warranty coverage set forth below, if you have purchased a five (5) year extended warranty 
(“

Five-Year Extended Warranty

”), and if the Product becomes defective in breach of the Limited Warranty above at any time 

during the five (5) year period after the date of the initial installation of the Product (the “

Five-Year Warranty Period

”), 

COULOMB will, upon written notice of the defect received during the Five-Year Warranty Period, either repair, provide 
replacement parts for the defective parts of the Product or replace the Product, at Coulomb’s election, if it proves to be 
defective; 

provided

, that COULOMB will not be responsible for the cost of any labor associated with the repair or 

replacement of any defective Product.

COULOMB’s OPTIONS

You acknowledge that

 r

eplacement products provided by Coulomb under each of the Limited Warranty and the Five-Year 

Extended Warranty may be remanufactured or reconditioned Products or, if the exact Product is no longer manufactured by 
COULOMB, a Product with substantially similar functionality (“

Replacement Products

”). Any Replacement Products so 

furnished will be warranted for the remainder of the original Warranty Period or ninety (90) days from the date of delivery of 
such Replacement Product, whichever is greater. Should COULOMB be unable to repair or replace the Product, 
COULOMB will refund the purchase price of the Product.

EXCLUSIONS FROM LIMITED WARRANTY AND FIVE-YEAR EXTENDED WARRANTY

IMPORTANT:

 The Limited Warranty and, if purchased, the Five Year Extended Warranty on your Product shall not apply to 

defects, or service repairs, resulting from any of the following:

• Alteration or modification of the Product in any way not approved in writing by COULOMB.

• Vandalism, abuse, damage or otherwise being subjected to problems caused by negligence (including 

but not limited to physical damage from being struck by a vehicle) or misapplication, or use of the 
Products other than as specified in the applicable COULOMB documentation.

• Installation or relocation of the Products unless performed by COULOMB or by a Coulomb authorized 

installer or service provider.

• Improper site preparation or maintenance.

• Damage as a result of accidents, extreme power surge, extreme electromagnetic field, acts of nature 

or other causes beyond the control of COULOMB.

• Use of the Product with software, interfacing, parts or supplies not supplied by COULOMB.

Содержание ChargePoint CT2023





















































Отзывы: