Coulomb Technologies ChargePoint CT2023 Скачать руководство пользователя

Страница: 10 / 52

ChargePoint® Charging Stations

2-2

Step 1 - Check boxes for correct contents

The CT2023 ChargePoint

Charging Station’s wall mount components ship in two boxes as shown below.

Main body assembly:

• Body* (1)

• Channel struts* (2)

• Cable hangers (2)

• Front cover plate (1)

• Filler panel* (1)

• 3/32” Allen wrench (1)

• Front panel* (1)

• Screws for cable hangers (4)

• Screws for holsters (6)

• Washers for cable hangers and

holsters (10)

• Wall anchor bolts with nuts and

washers (4)

• Hex head bolts and washers to

attach bracket to channel struts (4)

• Channel strut nuts (4)

• Installation Guide (1)

• Base plate mounting template (1)

*Body, front panel, and filler panel are
pre-assembled. Channel struts are attached to
body for shipping purposes only.

Installation
Guide

Front
panel

Body

Cable
hangers

Front
cover plate

Filler
panel

Allen
wrench

Screws for holsters

Washers for cable
hangers and holsters

CT2023

ChargePoint

Networked Charging Station

Installation

Guide

Part Number: 75-001089-01 Revision: 1.0

Coulomb Technologies Inc.
1692 Dell Ave.
Campbell, CA 95008-6901 USA
US toll free: +1-877-370-3802
www.coulombtech.com
www.mychargepoint.net

by Coulomb Technologies

Channel strut nuts

Wall anchor bolts
with nuts and
washers

Screws for cable
hangers

Channel
struts

Hex head bolts and
washers to attach
wall bracket to
channel strut

Содержание ChargePoint CT2023





















































Результаты поиска

Содержание ChargePoint CT2023

Отзывы:

Похожие инструкции для ChargePoint CT2023

Бренды по названию

Популярные бренды

Coulomb Technologies ChargePoint CT2023, Руководство по установке

Результаты поиска

Содержание ChargePoint CT2023

Отзывы:

Похожие инструкции для ChargePoint CT2023

Бренды по названию

Популярные бренды