COSMOGAS MYDENS Скачать руководство пользователя страница 53

Страница: 53 / 76

MYDENS

COSMOGAS

7 - USE

Err 51

Supply sensor circuit 2

(1005) open

Check that the electric resistance of the sensor

matches the graphics in chapter 8.22. Check the

electric cables for connection between the sensor

and the command board.

If the electric resistance does not match, replace it.

The electric circuit must be repaired if it is damaged.

Without either of the two previous cases, replace the

command and control board.

Err 52

Domestic hot water inlet

sensor 2 circuit (1002)

open

Check that the electric resistance of the sensor

matches the graphics in chapter 8.22. Check the

electric cables for connection between the sensor

and the command board.

If the electric resistance does not match, replace it.

The electric circuit must be repaired if it is damaged.

Without either of the two previous cases, replace the

command and control board.

Err 53

Fumes 1 sensor circuit

(1006) open

Check that the electrical resistance of the fumes

sensor 1006 matches the graphics in chapter 8.22

Check that the wires between the board and the

double fumes sensor are connected correctly

If the sensor does not match, the double fumes

sensor must be replaced.

If the wires are not connected correctly, the connec-

tions must be restored.

Err 54

Fumes 2 sensor circuit

(1014) open

Check that the electrical resistance of the fumes

sensor 1014 matches the graphics in chapter 8.22

Check that the wires between the board and the

double fumes sensor are connected correctly

If the sensor does not match, the double fumes

sensor must be replaced.

If the wires are not connected correctly, the connec-

tions must be restored

Err 55

Not applicable

Err 56

Return sensor circuit

(1007) in short circuit

condition

Check that the electric resistance of the sensor

matches the graphics in chapter 8.22. Check the

electric cables for connection between the sensor

and the command board.

If the electric resistance does not match, replace it.

The electric circuit must be repaired if it is damaged.

Without either of the two previous cases, replace the

command and control board.

Err 57

Supply sensor circuit 1

(1001) in short circuit

condition

Check that the electric resistance of the sensor

matches the graphics in chapter 8.22. Check the

electric cables for connection between the sensor

and the command board.

If the electric resistance does not match, replace it.

The electric circuit must be repaired if it is damaged.

Without either of the two previous cases, replace the

command and control board.

Err 58

Supply sensor circuit 2

(1005) in short circuit

condition

Check that the electric resistance of the sensor

matches the graphics in chapter 8.22. Check the

electric cables for connection between the sensor

and the command board.

If the electric resistance does not match, replace it.

The electric circuit must be repaired if it is damaged.

Without either of the two previous cases, replace the

command and control board..

Err 59

Domestic hot water inlet

sensor circuit (1002) in

short circuit condition

Check that the electric resistance of the sensor

matches the graphics in chapter 8.22. Check the

electric cables for connection between the sensor

and the command board.

If the electric resistance does not match, replace it.

The electric circuit must be repaired if it is damaged.

Without either of the two previous cases, replace the

command and control board.

Err 60

Fumes 1 sensor circuit

(1006) in short circuit

condition

Check that the electrical resistance of the fumes

sensor 1006 matches the graphics in chapter 8.22

Check that the wires between the board and the

double fumes sensor are connected correctly

If the sensor does not match, the double fumes

sensor must be replaced

If the wires are not connected correctly, the connec-

tions must be restored

Err 61

Fumes 2 sensor circuit

(1014) in short circuit

condition

Check that the electrical resistance of the fumes

sensor 1014 matches the graphics in chapter 8.22

Check that the wires between the board and the

double fumes sensor are connected correctly

If the sensor does not match, the double fumes

sensor must be replaced

If the wires are not connected correctly, the connec-

tions must be restored

Err 62

External temperature

sensor circuit (1004) in

short circuit condition

Check that the electric resistance of the sensor

matches the graphics in chapter 8.23. Check the

electric cables for connection between the sensor

and the command board.

If the electric resistance does not match, replace it.

The electric circuit must be repaired if it is damaged.

Without either of the two previous cases, replace the

command and control board.

Err 63

RESET key pressed too

many times in a very

brief period

7.19.3 - Diagnostics: alarms “AttE”

Alarm Description of the alarm

Checks

Solutions

AttE 65 Central heating plant

pressure too low for

more than 10 minutes

Check the pressure switch calibration pressure. FILL

musty appear when the pressure drops below 0.6

bar; check that there are no water leaks from the

central heating plant.

If the pressure switch is not calibrated correctly, it

must be replaced. If the plant has a leak it must be

repaired.

Содержание MYDENS













































































Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды