COSMOGAS MYDENS Скачать руководство пользователя страница 72

Страница: 72 / 76

MYDENS

COSMOGAS

The undersigned

COSMOGAS S.r.L.

, with Registered Office in via L. Da

Vincin° 16 - 47014 Meldola (FC) ITALY,

DECLARES

under its own responsibility that the product:

subject of this declaration, is in compliance with the model described in the

Type examination certificate

, whose reference is given in the table in

chapter 9 under “CE type certificate (PIN)” and meeting that required by the

Directives: Gas Appliances, (

2009/142/CE

former

90/396/CEE

), Efficiencys,

(

92/42/CEE

), Low Voltage, (

2006/95/CE

), Electromagnetic Compatibility,

(

2004/108/CEE

(the warranty number corresponds to the serial number)

This declaration is issued for that established by the above-mentioned
Directives.

Meldola (FC) ITALY, (Date of manufacture).

DATE OF MANUFACTURE

WARRANTY N°
GAS BOILER MODEL

12 - CE DECLARATION OF CONFORMITY

Содержание MYDENS













































































Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды