COSMOGAS MYDENS Скачать руководство пользователя страница 71

Страница: 71 / 76

MYDENS

COSMOGAS

ATTENTION !!!

The modification of these parameters could cause the appliance, and therefore the plant, to malfunction.

For this reason only a technician that has the awareness and in-depth knowledge of the appliances can modify

them.

To access this menu, introduce the bridge in the board as stated in figure 6.5 detail “A”.

11 - MENU FORCED BY INTERNAL ELECTRIC BRIDGE

Parameter

Description of the parameter

M.U.

Setting range

Factory value

Customised

value

3002

Selection type

From 50 to 55

See Figure 6.7

3012

Domestic hot water operating

mode

0 = No domestic hot water;

1 = Indirect water heater with temperature

sensor;

2 = Indirect water heater with thermostat;

3 = Instantaneous with flow switch;

4 = Microaccumulation with two sensors;

5 = Instantaneous with turbine;

model “P” = 5

model “B” = 1

model “C” = 0

3013

Plant fill automatic valve

0 = Valve disabled;

2 = Valvola abilitata;

3014

Instantaneous domestic hot

water pre-heat

OFF = No pre-heat

ON = with pre-heat

OFF

3015

Maximum central heating

temperature

°C

From 20 to 90

3016

Minimum central heating

temperature

°C

From 20 to 90

3020

Domestic hot water flow rate

sensor

0 = B; (MYDENS 15, 24 e 34)

1 = DN 8;

2 = DN 10;

3 = DN 15;

4 = DN 20;

5 = DN 25;

3021

2nd Fumes sensor (1014)

0 = Disabled;

1 = Enabled;

2 = Enabled with fumes exhaust anti-

closure pressure switch;

3022

Central heating minimum

pressure

bar

OFF... 0,3 to 5,1;

0,5

3033

Modulating pump

0 = Disabled;

1 = Enabled;

From 4 to 10 = Fixed speeds from 40% to

100%;

3034

Modulating pump delta T target

°C

From 5 to 40

3035

No function

3036

No function

3052

No function

Содержание MYDENS













































































Результаты поиска

Содержание MYDENS

Отзывы:

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию, Страница: 71 / 76

Результаты поиска

Содержание MYDENS

Отзывы: