manualshive.com logo in svg

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию, Страница: 49 / 76

Поделиться
Скачать
COSMOGAS MYDENS Скачать руководство пользователя страница 49

49

MYDENS

COSMOGAS

7.19 - Diagnostics

During  normal  appliance  operation,  the  visual  display  “N” 

in figure 7.1, continuously shows the working status of the 

appliance via the following indications:

7 - USE

Parameter

Description of the parameter

Display on visual display “N” in figure 7.1

AFro

Anti-freeze function active

Boiler temperature (°C)

AttE

Boiler not in block but in attention mode 

Attention code (see chapter 7.19.3 for decoding)

FILL

Plant pressure too low, perform filling (see chapter 6.1.3)

FILL

Fixed on = Domestic hot water service on but not active

On flashing =  Domestic hot water service on and active

Domestic hot water temperature (°C)

Fixed on = =Central heating service on but not active

On flashing = =Central heating service on and active

Central heating temperature (°C)

Loc

Boiler blocked. To reset, press 

RESET

. If the block occurs 

frequently, contact a professionally qualified technician.

Block code (see chapter 7.19.1 for decode)

Err

Boiler in error mode. Functioning can only be restored by 

solving the cause of the anomaly. Contact a professionally 

qualified technician

Error code (see chapter 7.19.2 for decode)

ALEg

Anti-legionella function running (see chapter 7.12).

It will end on reaching the water temperature of 60°C inside the 

indirect water heater.

Indirect water heater temperature (°C)

SEr

Maintenance request for the boiler

Appliance temperature (°C)

Содержание MYDENS













































































Отзывы:

Нет отзывов