COSMOGAS MYDENS Скачать руководство пользователя страница 63

Страница: 63 / 76

MYDENS

COSMOGAS

8.20 - Checking the ionisation current

In any operating status, also during verifications of minimum

and maximum power stated in chapter 8.19, the ionisation
current value can be consulted on parameter

1008

present

in the “User menu” (chapter 7.17). This value must be between

1.5 and 3 uA (microampere) at minimum power and between

5 and 8 uA at maximum power.

8.21 - Checking combustion efficiency

On the basis of national laws regarding gas appliances, the

combustion efficiency must be checked periodically;

To do this, operate exactly as stated in chapter 6.8 and

check, along with the CO2, also the combustion efficiency,

which must be over 96%.

Figure 8.18 - Water sensors curve

Figure 8.19 - External temperature sensor curve

8 - MAINTENANCE

8.22 - Water temperature

measurement sensors

The temperature sensors are positioned on the boiler’s

exchanger body. The electric resistance existing between

the two contacts of the sensor, must correspond with that

stated in figure 8.18.

The temperature sensors are:

1001

1002

1003

1005

1006

1007

and

1014

, the positioning of

which can be verified in figure 3.1.

8.23 - External temperature sensor

On request, the external temperature sensor can be
connected to the boiler

1004

(see chapter 5.14.4). The

electric resistance existing between the two contacts of the

sensor, must correspond with that stated in figure 8.19.

Содержание MYDENS













































































Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды