COSMOGAS MYDENS Скачать руководство пользователя страница 54

Страница: 54 / 76

MYDENS

COSMOGAS

8.1 - General recommendations

It is recommended to perform regular yearly maintenance of

the central heating plant for the following reasons:

- to maintain high efficiency of the appliance and therefore

save fuel;

- to maintain a high level of safety;

- to maintain the level of environmental compatibility of the

combustion high;

In order to maintain the frequency of maintenance, there
is a parameter present

2080

in the installer menu (see

chapter 7.18), which is used to activate the maintenance
call (Service) along with the parameter

2081

which is

used to set the operating days that must pass between one

call and the next.

The control system identifies the operating days, checking

the burner activity time.

Proceed as follows to activate the call service:

1.- access the Installer menu (see chapter 7.18) and set

parameter

2080

;

2.- access parameter

2081

and set the boiler operating

days which must pass between one call and the next.

The call will be completed with

SEr

on the display. To

remove the wording

SEr

and renew the call period,

operate as follows:

1.- access the “Installer menu”;

2.- access the parameter

2080

, set it on

rESE

and

press the RESET key.

3.- exit the Installer menu by pressing the RESET key for 5

seconds.

The call time is now renewed and

SEr

appears on the

display.

ATTENTION !!! Appliance maintenance must

only be performed by a professionally qualified

technician.

ATTENTION !!! Before every maintenance

operation, disconnect the appliance from the electric

power supply, using the relevant switch in the vicinity.

ATTENTION !!! Close the gas cock before any

maintenance operation

8 - MAINTENANCE

Содержание MYDENS













































































Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды