COSMOGAS MYDENS Скачать руководство пользователя страница 27

Страница: 27 / 76

MYDENS

COSMOGAS

5.16.4 - “Split 80/80PP” System (Type C43;

C53; C83): installation examples

In figure 5.17 two examples of installation are given:

- exhaust into chimney with collection of condensate inside

the boiler itself.

The horizontal part of the fumes exhaust side must be inclined

towards the boiler.

The intake must slope towards the outside to prevent rain

water entering.

- exhaust to the outside directly with the boiler pipes with

condensate collection inside the boiler itself.

The intake must slope towards the outside to prevent rain

water entering.

in figure 5.18 it is possible to see a separated type of fumes

exhaust, where fumes exhaust was realised with flexible hose

in polypropylene for piping of technical cells.

The condensate produced in the vertical pipe must all be

conveyed into the boiler.

The intake must slope towards the outside to prevent rain

water entering.

Figure 5.17 - Example of “80/80 PP System”

installation

Figure 5.18 - Example of “80/80 PP System” installation

5 - INSTALLATION

Содержание MYDENS













































































Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды