COSMOGAS MYDENS Скачать руководство пользователя страница 28

Страница: 28 / 76

MYDENS

COSMOGAS

020002.01.012

5.16.5 - “60/100PP vertical coaxial” System

(polypropylene) (C13; C33)

The appliance is supplied as per standard without fittings

for the connection of the fumes exhaust/air intake. To

connect the boiler to a 60/100 coaxial system, the relevant

kit must be requested and must be installed as in figure

5.19.

ATTENTION !!! Scrupulously follow the installation

phases of the coaxial pipe as illustrated in figure 5.21. In

particular:

1.- introduce the coaxial pipe “C” inside the bend “A”;

2.- fix the external pipe using the stainless steel self-threading

screws “B”.

ATTENTION !!! The coaxial exhaust and

intake pipes must be appropriately sustained via rigid

brackets positioned non more than 1 metre from each

other. The brackets must be fixed to rigid walls that can

support the weight of the pipe itself.

ATTENTION !!! Once these operations have

been performed, check that the exhaust/intake terminal

is exposed to the outdoors with the tolerances given in

figure 5.25



Take particular care with the installation of pipes in the part

that passes through the wall to the outside. The normal

maintenance operations must always be possible, therefore

install the pipes in a sheath so that they can be slid out.



The horizontal tracts must always have an inclination of at

least 2% towards the boiler.



The fumes exhaust/air intake pipe can be extended up to

a maximum distance as indicated in the table in chapter

9 at the end of the manual. Every 90° bend has a loss

equivalent to 1 metre of linear pipe. Every 45° bend has a

loss equivalent to 0.5 m of pipe.

Figure 5.19 - Installation of vertical coaxial system

Figure 5.20 - Quotes and hole centre to centre

distances for coaxial drain pre-installation

Figure 5.21 - Positioning the coaxial pipe

5 - INSTALLATION

Содержание MYDENS













































































Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды

COSMOGAS MYDENS, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MYDENS

Отзывы:

Похожие инструкции для MYDENS

Бренды по названию

Популярные бренды