manualshive.com logo in svg

Cooper safety CEAG EURO US.1, Монтаж и эксплуатация

Поделиться
Скачать
Cooper safety CEAG EURO US.1 Скачать руководство пользователя страница 49

Mounting and Operating Manual

Central Battery System EURO ZB.1

49

CEAG Notlichtsysteme GmbH

Disconnecting/Switching-on an Emergency Lighting 

System under Battery  Supply

12.1 

Disconnecting/Switching-on an Emergency Lighting System  

 

under Battery Supply

  Before re-connecting the battery sup-

ply at the connections of the battery 
bank switch on the mains power 
supply system and make sure that the 
system is blocked (see 26). Following 
this, you may switch on the battery 
supply on the battery bank.

The above instructions apply analogously 
in case that the mains  supply and/or 
battery supply of a EURO ZB.1 or EURO 
US.1 control cabinet shall be disconnec-
ted or switched on.

  Do not switch the mains power supp-

ly of a control cabinet  (EURO ZB.1 or 
EURO US.1) off or on under load (ie. 
with the final circuits being switched 
on). 

  Do not switch the battery supply of a 

control cabinet  (EURO ZB.1 or EURO 
US.1) off or on under load (ie. with the 
final circuits being switched on).

 

  Before you disconnect or switch on 

the mains and/or battery supply make 
sure that the control system has been 
blocked (see 12.3).

This is done via the menu item „Block/
Enable Unit“ in menu 26 „Blocking, Ack-
nowledgment“ of the control software.

Danger!
Turning the mains  supply on or 
off within the pertinent distributor 
should  never take place under 
load  (ie. when final circuits are 
switched on)! 

If the power supply to the general lighting 
system or the mains  supply of the emer-
gency lighting system fails or is switched 
off the emergency lighting system control 
will reverse to battery  supply. In this 
case a voltage of 216 V DC is applied, so 
take care: 

Danger!
Never  disconnect or connect 
lines under load to the battery 
bank (battery cabinet or battery 
rack)!

The same applies if the load-break switch 
for battery  supply in the control cabinet 
(EURO ZB.1 / EURO US.1) is opened (or 
closed) under load!

  Before disconnecting the emergency 

lighting system on the distributor of 
the general mains  supply and/or the 
connections of the battery bank for 
battery supply make sure to block the 
plant as described in Section 12.3.

  Following this, first disconnect the 

battery supply and then disconnect 
the mains supply.

  Take safety measures to ensure that 

plant remains disconnected as long 
as you work on the system or until the 
operationally safe state of the system 
has been restored.

Attention!
In case several systems (EURO 
ZB.1 with EURO US.1 substati-
ons) are supplied with power from 
a battery bank all systems must 
first be blocked!
Start with disconnecting the lo-
west level of the EURO US.1 sub-
stations before you disconnect 
the EURO ZB.1 central battery 
system!

12.2 

Disconnecting/Swit-

ching-on a  

EURO ZB.1  

Control Cabinet  

or EURO US.1

12.3 

Block/Release the 

Control of a EURO 

ZB.1 Control Cabinet   

or EURO US.1

Содержание CEAG EURO US.1













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды