CONVEY-ALL CST-1550 Скачать руководство пользователя страница 49

Страница: 49 / 62

Operator’s Manual: CST-1550

01.2019

4-7

By following a careful service and maintenance
program for your tender, you will enjoy many
years of trouble-free service.

Note:

Refer to the engine manual for complete

details on your particular model.

ROTATING PART HAZARD

Turn off engine. Wait for belt and rollers to

stop moving, before working on the belt.

4.3.1 Conveyor Belt Tension:

The tension of both the slave and rear (incline)
conveyor belts should be checked daily to insure
proper function.

Note:

Belt is tensioned correctly when it does
not slip on the drive roller when loaded.

Belt Tension of Slave Conveyor:

1. Loosen the roller bearing housings at the tail.

2. The tension is set and controlled by the

springs on both sides of the slave conveyor
belt.

Tighten, or loosen the tension bolts, so the
springs have a measurement of 3-3/4” (95
mm).

3. Tighten the roller bearing housing.

4. Measure the spring lengths to be equal.

Fig 67 - Slave conveyor tension bolt and springs

Fig 68 - Adjustment bolts on rear conveyor

Belt Tension of Rear (Incline) Conveyor:

5. Loosen the roller bearing housings at the

rear conveyor discharge.

6. Tighten or loosen the adjustment bolts for

correct tension of the paddle belt.

7. Tighten the roller bearing housings.

4.3 MAINTENANCE PROCEDURES

Содержание CST-1550































































Результаты поиска

Содержание CST-1550

Отзывы:

Похожие инструкции для CST-1550

Бренды по названию

Популярные бренды

CONVEY-ALL CST-1550, Руководство оператора

Результаты поиска

Содержание CST-1550

Отзывы:

Похожие инструкции для CST-1550

Бренды по названию

Популярные бренды