Conexant H08-15350 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 120

background image

Command Reference Manual

1118

Conexant

5-5

5.2.2 Voice Commands

5.2.2.1 +VIP - Voice Initialize All Parameters

This command causes the modem to initialize all voice parameters to their default values.

Syntax

+VIP

Result Code

OK

ERROR

If not in Voice Mode.

5.2.2.2 +VRX - Start Modem Receive (Record)

This command causes the modem to start the voice reception process.

Syntax

+VRX<n>

Defined Values

<n>

Decimal number corresponding to the selected option.

0

Start receive voice without periodic tone production during a voice receive operation.

1

Start receive voice with periodic tone production during a voice receive operation.

Result Codes

OK

<n> = 0 or 1.

ERROR

Otherwise, or if not in Voice Mode.

5.2.2.3 +VTR - Start Voice Transmission and Reception (Voice Duplex)

This command causes the modem to start the voice transmission and reception process (Voice Duplex) without either
acoustic echo cancellation or line echo cancellation. The modem begins the Voice Duplex State by returning the CONNECT
result code to the DTE. The modem then sends <DLE> shielded voice data to the DTE, and the DTE can send <DLE>
shielded voice data to the modem. The modem will accept data from the DTE and send data to the DTE in the format
previously selected by the +VSM command, and use the flow control method selected by the +IFC command.

The modem signals termination of the voice data stream by appending a <DLE><ETX> command and padding out to an octet
boundary if needed. The modem will issue the <DLE><ETX> character pair (thereby ending the modem to DTE voice data
flow) followed by the OK result code, and return to the command mode after the modem has completely transmitted the
contents of its buffer.

There are two methods to leave the Voice Duplex State: the DTE sending a <DLE><^> shielded code or the inactivity timer
elapsing in the modem. The Voice Command State is entered upon Voice Duplex State termination.

This command will function when the input and output are from/to the same I/O device, such as local handset, line, or
mic/speaker.

Syntax

+VTR

Result Codes

OK

Upon command acceptance.

ERROR

The modem is not connected to the line and a non-line device.

«
...
97
98
99
100
101
...
»

Содержание H08-15350

























































































































Отзывы:

Нет отзывов

Похожие инструкции для H08-15350

Бренд: Radyne Страницы: 192

Бренд: Patton electronics Страницы: 28

Бренд: FTS Страницы: 2

Бренд: Tenda Страницы: 29

Бренд: Abocom Страницы: 1

Бренд: Cisco Страницы: 30

Бренд: Scientific Atlanta Страницы: 92

Бренд: Go Страницы: 2

Бренд: Arris Страницы: 1

Бренд: Zte Страницы: 16

Бренд: Eaton Страницы: 2

Бренд: Elster Страницы: 8

Skywire NL-LTE-TNAG

Бренд: NimbeLink Страницы: 8

Бренд: Ubee Страницы: 74

InduBox PSTN III

Бренд: Bausch Datacom Страницы: 24

Бренд: Bausch Datacom Страницы: 27

Бренд: NETGEAR Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды