Conexant H08-15350 Скачать руководство пользователя страница 114

Страница: 114 / 120

Command Reference Manual

Conexant

1118

5-20

5.2.3 Speakerphone Commands

5.2.3.1 +VSP - Speakerphone ON/OFF

This command turns the speakerphone ON or OFF

Syntax

+VSP=<mode>

Defined Values

<mode>

Decimal number corresponding to the selected option.

The speakerphone function is OFF.

The speakerphone function is ON.

Reporting Current or Selected Values

Command:

+VSP?

Response:

+VSP: <mode>

Example:

+VSP: 0

For the default setting.

Reporting Supported Range of Parameter Values

Command:

+VSP=?

Response:

+VSP: (<mode> range)

Example:

+VSP: (0,1)

Result Codes

<mode> = 0 or 1.

ERROR

Otherwise, or if not in Voice Mode.

5.2.3.2 +VDX - Speakerphone Duplex Mode

This command selects speakerphone half-duplex or full duplex mode.

Syntax

+VDX=<mode>

Defined Values

<mode>

Decimal number corresponding to the selected option.

The speakerphone mode is half duplex.

The speakerphone mode is full duplex.

Reporting Current or Selected Values

Command:

+VDX?

Response:

+VDX: <mode>

Example:

+VDX: 0

For the default setting.

Reporting Supported Range of Parameter Values

Command:

+VDX=?

Response:

+VDX: (<mode> range)

Example:

+VDX: (0,1)

Result Codes

<mode> = 0 or 1.

ERROR

Otherwise, or if not in Voice Mode.

Содержание H08-15350

























































































































Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды

Conexant H08-15350, Справочное руководство

Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды