Conexant H08-15350 Скачать руководство пользователя страница 32

Страница: 32 / 120

Command Reference Manual

Conexant

1118

3-14

3.2.2.8 &K - Flow Control

This command defines the DTE/DCE (terminal/modem) flow control mechanism.

Syntax

&K[<value>]

Defined Values

<value>

Decimal number corresponding to the selected option.

Disables flow control.

Enables RTS/CTS flow control. (Default for data modem modes.)

Enables XON/XOFF flow control.

Included for compatibility only and has no effect other than returning an OK result code.

Result Codes

<value> = 0, 3, 4, 5, or 6.

ERROR

Otherwise.

3.2.2.9 &M - Asynchronous/Synchronous Mode Selection

This command is included for compatibility only and has no effect other than returning a result code. The only valid values
are 0-3.

Syntax

&M[<mode>]

Defined Values

<mode >

Decimal number corresponding to the selected value: 0-3.

Result Codes

<mode> = 0 to 3.

ERROR

Otherwise.

3.2.2.10 &Q - Sync/Async Mode

This command determines the DTR operating mode. (Also, see \N.)

NOTE: When the &Q0 is issued to select the mode, the subsequent connect message will report the DCE speed regardless
of the W command and S95 settings.

Syntax

&Q[<mode>]

Defined Values

<mode >

Decimal number corresponding to the selected mode:

Selects asynchronous operation in normal mode (speed buffering)

Selects asynchronous operation in error correction mode

Selects asynchronous operation in normal mode (speed buffering).

Result Codes

<mode > = 0-3, 5, 6.

ERROR Otherwise.

Содержание H08-15350

























































































































Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды

Conexant H08-15350, Справочное руководство

Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды