Conexant H08-15350 Скачать руководство пользователя страница 53

Страница: 53 / 120

Command Reference Manual

1118

Conexant

3-35

3.2.7.4 +A8C: - Calling Tone Indication

This indication is issued by an answering modem, if +A8E,<v8a>

≠

0, to indicate detection of 1100 Hz or 1300 Hz calling

tones, or sigC signals, as defined in T.30, V.8 and in V.25.

Indication Syntax

+A8C: <type><CR>

Defined Values

<type>

Decimal number which indicates the corresponding detected calling tone.

The modem concluded answer tone transmission without reporting detection of any
calling tone.

CNG tone (1100 Hz) detected.

1300 Hz V.25 data modem calling tone detected.

sigC signal: V.32/V.32

bis AA tone detected.

Example

+A8C: 1

For CNG tone detected.

3.2.7.5 +A8A: - Answer Signal Indication

This indication is issued by a calling modem, if +A8E <v8o>

≠

0, to indicate detection of an answering signal.

Indication Syntax

+A8A:<type><CR>

Defined Values

Decimal number which indicates the corresponding detected answer signal.

The modem timed out waiting for an answering signal.

V.8 ANSam signal (2100 Hz with amplitude modulation) detected.

V.25 answer tone (2100 Hz) detected.

V.25 answer tone with phase reversals detected. (Note)

sigA signal: V.21 Ch2 with flags (e.g., T.30 control preamble) detected.

sigA signal: V.22bis USB1 signal detected.

sigA signal: V.32bis AC signal detected.

sigA signal: V.34 ToneA signal detected.

Example

+A8A:1

For V.8 ANSam signal (2100 Hz with amplitude modulation) detected.

Содержание H08-15350

























































































































Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды

Conexant H08-15350, Справочное руководство

Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды