Conexant H08-15350 Скачать руководство пользователя страница 97

Страница: 97 / 120

Command Reference Manual

1118

Conexant

5-3

5.1.2 <DLE> Shielded Codes Sent to the Modem (DCE)

Table 5-3 lists the supported <DLE> shielded codes sent to the modem in the expression <DLE><code>. The number in
parenthesis in the second column corresponds to the T.50 equivalent.

Table 5-3. Supported <DLE> Shielded Codes Sent to the Modem (DCE)

Code

Simple Action Command Description

<DLE>

(1/0)

Two contiguous <DLE><DLE> codes indicate a single <DLE> in the data stream
("Immediate Command" or "Stream Command").

(7/5)

[Action Numbers 0 and 3] Increase the volume or gain by one unit ("Immediate
Command").

(6/4)

[Action Numbers 1 and 4] Decrease the volume or gain by one unit ("Immediate
Command").

(7/0)

[Action Number 9] Pause.

(7/2)

[Action Number 10] Resume.

<ETX>

(0/3)

[Action Number 11] End Voice Transmit State ("Stream Command").

<CAN>

(1/8)

[Action Number 12] Clear transmit buffer of voice data ("Immediate Command").

(2/1)

[Action Number 15] Receive abort ("Immediate Command").

(5/E)

End Voice Duplex State (see +VTR command).

Содержание H08-15350

























































































































Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды

Conexant H08-15350, Справочное руководство

Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды