Conexant H08-15350 Скачать руководство пользователя страница 102

Страница: 102 / 120

Command Reference Manual

Conexant

1118

5-8

5.2.2.5 +VTX - Start Modem Transmit (Playback)

This command causes the modem to start the voice transmission process.

Syntax

+VTX

Result Codes

CONNECT

The modem accepts the command.

ERROR

The modem is not connected to at least one off-hook telephone line or one non-telephone line.

5.2.2.6 +VGR - Voice Gain Receive (Record Gain)

This command causes the modem to set the gain for received voice samples.

Syntax

+VGR=<gain>

Defined Values

<gain>

Decimal number between 0 and 255 corresponding to the gain.

Reporting Current or Selected Values

Command:

+VGR?

Response:

+VGR: <gain>

Example:

+VGR: 0

For the default setting.

Reporting Supported Range of Parameter Values

Command:

+VGR=?

Response:

+VGR: <gain> range

Example:

+VGR: 0-255

Result Codes

<gain> = 0-255.

ERROR

Otherwise, or if not in Voice Mode.

5.2.2.7 +VGT - Voice Gain Transmit (Playback Volume)

This command causes the modem to set the volume level.

Syntax

+VGT=<level>

Defined Values

<level>

Decimal number (120-135) corresponding to the volume level.

Reporting Current or Selected Values

Command:

+VGT?

Response:

+VGT: <level>

Example:

+VGT: 128

For the default setting.

Reporting Supported Range of Parameter Values

Command:

+VGT=?

Response:

+VGT: <level> range

Example:

+VGT: 120-135

Result Codes

<level> = 120-135.

ERROR

Otherwise, or if not in Voice Mode.

Содержание H08-15350

























































































































Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды

Conexant H08-15350, Справочное руководство

Результаты поиска

Содержание H08-15350

Отзывы:

Похожие инструкции для H08-15350

Бренды по названию

Популярные бренды