Conexant H08-15350 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 120

background image

Command Reference Manual

1118

Conexant

3-15

3.2.2.11 +IPR - Fixed DTE Rate

This numeric extended-format parameter specifies the data rate at which the modem will accept commands during online
operation. It may be used to select operation at rates at which the modem is not capable of automatically detecting the data
rate being used by the DTE. Specifying a value of 0 disables the function and allows operation only at rates automatically
detectable by the modem. The specified rate takes effect following the issuance of any result code(s) associated with the
current command line.

The <rate> specified does not apply in OnLine Data State if Normal Mode (Direct Mode) of operation is selected.

Syntax

+IPR=<rate>

Defined Values

<rate>

Specifies the DTE-modem interface operation rate in bits/s. The available rates are:

0, 2400, 4800, 9600, 19200, 38400, or 57600

If unspecified or set to 0, automatic detection is selected and the character format is also forced to
autodetect, +ICF=0.

If the rate specified is not supported by the modem, an ERROR result code will be returned.

Reporting Current or Selected Values

Command:

+IPR?

Response:

+IPR: <rate>

Example 1:

+IPR: 0

for automatic rate detection.

Example 2:

+IPR: 57600

for 57600 bps.

Reporting Supported Range of Parameter Values

Command:

+IPR=?

Response:

+IPR (<rate> range)

Example:

+IPR: (0, 2400,4800,9600,19200,38400,57600)

«
...
31
32
33
34
35
...
»

Содержание H08-15350

























































































































Отзывы:

Нет отзывов

Похожие инструкции для H08-15350

Бренд: PROLiNK Страницы: 19

Бренд: Aztech Страницы: 32

Бренд: ACS Страницы: 45

Бренд: Telit Wireless Solutions Страницы: 74

Бренд: Comet64 Страницы: 5

Бренд: Enfora Страницы: 98

E90-DTU-433L33-V8

Бренд: Ebyte Страницы: 19

Бренд: Cooper Bussmann Страницы: 74

Бренд: ERE Wireless Страницы: 20

Fritzbox 6660 Cable

Бренд: Fritz! Страницы: 12

Бренд: K1EL Страницы: 37

Бренд: SMC Networks Страницы: 48

Smart Hub SWO-HUB01K

Бренд: SwannOne Страницы: 2

Бренд: Flightcell Страницы: 12

DirecWay DW4020

Бренд: Hughes Network Страницы: 102

Бренд: Raymar Страницы: 23

Бренд: Zte Страницы: 13

Бренд: RACOM Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды